Kenwood TS-590S User Manual - Page 19

SELECTING A BAND Press [1.8 (1)] ~ [50 (0)] or [GENE] to select your desired band. • Press each key to cycle through the 3 default settings as shown in the table below. • Each setting can be modified with your personal preference for frequency and mode. After modifying the setting, pressing the key again will save that setting. Frequency Default Setting (MHz)/ Key Type Range Mode (MHz) 1 2 3 K [1.8 (1)] E 1.62 ~ 2 1.8/ CW 1.83/ CW 1.82/ CW 1.84/ CW 1.84/ CW 1.81/ CW K [3.5 (2)] E 3 ~ 4 3.8/ 3.5/ 3.7/ LSB LSB LSB 3.79/ LSB [7 (3)] K E 7.1/ 7.2/ 6.5 ~ 7.5 7.0/ LSB LSB 7.05/ LSB 7.1/ LSB LSB [10 (4)] All 10 ~ 10.5 10.1/ CW 10.12/ 10.14/ CW CW [14 (5)] All 13.5 ~ 14.5 14.0/ USB 14.1/ USB 14.2/ USB [18 (6)] All 18 ~ 19 18.068/ 18.11/ 18.15/ USB USB USB [21 (7)] All 20.5 ~ 21.5 21.0/ USB 21.15/ USB 21.3/ USB [24 (8)] All 24 ~ 25 24.89/ 24.93/ 24.95/ USB USB USB [28 (9)] All 27.5 ~ 30 28/ USB 28.3/ USB 29/ FM K [50 (0)] E 50 ~ 54 50.125/ 50/ USB 51/ USB 50.15/ FM USB K [GENE] E 0.03 ~ 60 0.1357/ CW 5.3305/ USB 5.2585/ USB 5.4035/ USB 3 OPERATING BASICS SELECTING A MODE Press one of the following keys to select your desired mode set: [LSB/USB], [CW/FSK (REV)], or [FM/AM (FM-N)]. [LSB/USB] Press to select LSB or USB mode. Press again to toggle between LSB and USB mode. While in LSB mode, press [DATA] to toggle between LSB and LSB-DATA mode. Likewise, while in USB mode press [DATA] to toggle between USB and USBDATA mode. Additionally, while in LSB-DATA or USB-DATA mode, you can press [LSB/USB] to toggle between LSBDATA and USB-DATA mode. [CW/FSK (REV)] Press to select CW or FSK mode. Press again to toggle between CW and FSK mode. While in CW mode, press and hold [CW/FSK (REV)] to toggle between CW and CW-R mode. Likewise, while in FSK mode press and hold [CW/FSK (REV] to toggle between FSK and FSK-R mode. Additionally, while in CW-R or FSK-R mode, you can press [CW/FSK (REV)] to toggle between CW-R and FSK-R mode. [FM/AM (FM-N)] Press to select FM or AM mode. Press again to toggle between FM and AM mode. While in FM mode, press and hold [FM/AM (FM-N)] to toggle between FM and FM-NAR mode, or press [DATA] to toggle between FM and FM-DATA mode. Additionally, while in FM-NAR mode, press [DATA] to toggle between FM-NAR and FM-NAR-DATA mode and while in FM-DATA mode, press and hold [FM/AM (FM-N)] to toggle between FM-DATA and FM-NARDATA mode. Access Menu No. 23 then press [M.IN] to select "on" to turn the Auto Mode selection ON. When it is ON, " " appears. As a default, if you change the frequency above or below 9.5 MHz, the transceiver automatically switches modes; LSB for frequencies under 9.5 MHz and USB for frequencies 9.5 MHz and over. You can further add the frequency borders to the Auto Mode selection {page 51}. 11