Kodak ESP 7250 Extended user guide - Page 11

Connecting to a wireless network, Before you connect - setup

Get Kodak ESP 7250 - All-in-one Printer PDF manuals and user guides View all Kodak ESP 7250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

KODAK ESP 7200 Series All-in-One Printer Connecting to a wireless network To connect your printer to an 802.11 wireless (Wi-Fi) network, refer to the following information. Before you connect You need: • A computer equipped with a network interface card or wireless networking support. • A working 802.11 wireless network. Kodak recommends that you use a wireless access point/router that uses Dynamic Host Configuration Protocol (DHCP). • Your network name (SSID - Service Set Identifier). You can obtain your SSID from the wireless access point, most commonly a router, using the router's embedded Web server. See the manufacturer's documentation provided with your wireless system for more information. • Your Wired Equivalent Privacy (WEP) key or Wi-Fi Protected Access (WPA/WPA2) passphrase. • To be sure to temporarily disable your firewall until the printer is successfully installed and communicating. Connecting to a wireless network using the WiFi Setup Wizard You can use the WiFi Setup Wizard on the printer to connect to your wireless network. Read the following procedures and use the one that is appropriate for your network setup. Connecting to a listed network See Before you connect to determine what is needed to connect your printer to the network. To connect to a listed network using the WiFi Setup Wizard: 1. Press Home. 2. Press to select Network Settings, then press OK. 3. With WiFi Setup Wizard selected, press OK. NOTE: The Wi-Fi radio is turned on automatically when you select WiFi Setup Wizard. www.kodak.com/go/aiosupport 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
www.kodak.com/go/aiosupport
5
KODAK ESP 7200 Series All-in-One Printer
Connecting to a wireless network
To connect your printer to an 802.11 wireless (Wi-Fi) network, refer to the following
information.
Before you connect
You need:
•
A computer equipped with a network interface card or wireless networking
support.
•
A working 802.11 wireless network. Kodak recommends that you use a wireless
access point/router that uses Dynamic Host Configuration Protocol (DHCP).
•
Your network name (SSID - Service Set Identifier). You can obtain your SSID
from the wireless access point, most commonly a router, using the router’s
embedded Web server. See the manufacturer’s documentation provided with
your wireless system for more information.
•
Your Wired Equivalent Privacy (WEP) key or Wi-Fi Protected Access
(WPA/WPA2) passphrase.
•
To
be sure to
temporarily disable your firewall until the printer is successfully
installed and communicating.
Connecting to a wireless network using the WiFi Setup Wizard
You can use the WiFi Setup Wizard on the printer to connect to your wireless
network. Read the following procedures and use the one that is appropriate for your
network setup.
Connecting to a listed network
See
Before you connect
to determine what is needed to connect your printer to the
network.
To connect to a listed network using the WiFi Setup Wizard:
1. Press
Home
.
2. Press
to select
Network Settings
, then press
OK
.
3. With
WiFi Setup Wizard
selected, press
OK
.
NOTE: The Wi-Fi radio is turned on automatically when you select WiFi Setup
Wizard.