Lantronix XPort APS: Modbus Protocol User Guide - Page 11

Basic Commands D/S/Q - reset factory default

Get Lantronix XPort PDF manuals and user guides View all Lantronix XPort manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

3: Configuring Modbus Figure 3-1. Setup (Configuration) Mode Screen Model: Device Server Plus+! (Firmware Code:AM) Modbus/TCP to RTU Bridge Setup 1) Network/IP Settings: IP Address 0.0.0.0/DHCP/BOOTP/AutoIP Default Gateway not set --Netmask not set --- 2) Serial & Mode Settings: Protocol Modbus/RTU,Slave(s) attached Serial Interface 9600,8,N,1,RS232 3) Modem Control Settings: RTS Output Fixed High/Active 4) Advanced Modbus Protocol settings: Slave Addr/Unit Id Soutce . . Modbus/TCP header Modbus Serial Broadcasts . . . Disabled (Id=0 auto-mapped to 1) Modbus/TCP pipeline . . . . . Enabled (new MB/TCP requests queued in FIFO) MB/TCP Exception Codes . . . . Yes (return 0x0A and 0x0B) Char, Message Timeout . . . . 00050msec, 05000msec 7) Security Settings: SNMP Enabled SNMP Community Name . . . . . public Telnet Setup Enabled TFTP Download Enabled Port 77FEh Enabled Web Server Enabled Web Setup Enabled Enhanced Password Disabled Port 77F0h Enabled D)efault settings, S)ave, Q)uit without save Select Command or parameter set (1. . . 7) to change: Basic Commands (D/S/Q) Figure 3-1. Setup (Configuration) Mode Screen shows the main IAP Device Server configuration menu. The IAP Device Server offers three basic options. Default Settings (D) Entering D resets all parameters to the factory default as shown above. Only the IP address does not change. Although not required, selecting this option immediately after reloading the firmware and saving it ensures that the unit resets. Save (S) Entering S saves the currently displayed parameter settings into non-volatile memory and exits configuration mode. This option triggers a reset. Quit Without Saving (Q) Entering Q cancels any parameter changes you have made and exits configuration mode. This option triggers a reset. Modbus Protocol User Guide 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
3: Configuring Modbus
Modbus Protocol User Guide
11
Figure 3-1. Setup (Configuration) Mode Screen
Model: Device Server Plus+! (Firmware Code:AM)
Modbus/TCP to RTU Bridge Setup
1) Network/IP Settings:
IP Address . . .
. . . . . .
- 0.0.0.0/DHCP/BOOTP/AutoIP
Default Gateway
. . . . . . . --- not set ---
Netmask
. . . . . . . . . . . --- not set ---
2) Serial & Mode Settings:
Protocol . . . . . . . . . . . Modbus/RTU,Slave(s) attached
Serial Interface . . . . . . . 9600,8,N,1,RS232
3) Modem Control Settings:
RTS Output . . . . . . . . . . Fixed High/Active
4) Advanced Modbus Protocol settings:
Slave Addr/Unit Id Soutce
. . Modbus/TCP header
Modbus Serial Broadcasts . . . Disabled (Id=0 auto-mapped to 1)
Modbus/TCP pipeline
. . . . . Enabled (new MB/TCP requests queued in FIFO)
MB/TCP Exception Codes . . . . Yes (return 0x0A and 0x0B)
Char, Message Timeout
. . . . 00050msec, 05000msec
7) Security Settings:
SNMP . . . . . . . . . . . . . Enabled
SNMP Community Name
. . . . . public
Telnet Setup . . . . . . . . . Enabled
TFTP Download . . . . .
. . . Enabled
Port 77FEh . . . . . . . . . . Enabled
Web Server . . . . . . . . . . Enabled
Web Setup . . . . . . .
. . . Enabled
Enhanced Password. . . . . . . Disabled
Port 77F0h . . . . . . . . . . Enabled
D)efault settings, S)ave, Q)uit without save
Select Command or parameter set (1. . . 7) to change:
Basic Commands (D/S/Q)
Figure 3-1. Setup (Configuration) Mode Screen
shows the main IAP Device Server configuration
menu. The IAP Device Server offers three basic options.
Default Settings (D)
Entering
D
resets all parameters to the factory default as shown above. Only the IP address does
not change. Although not required, selecting this option immediately after reloading the firmware
and saving it ensures that the unit resets.
Save (S)
Entering
S
saves the currently displayed parameter settings into non-volatile memory and exits
configuration mode. This option triggers a reset.
Quit Without Saving (Q)
Entering
Q
cancels any parameter changes you have made and exits configuration mode. This
option triggers a reset.