Lenovo NetVista IBM PC300 (Type 2169) - Hardware Maintenance Manual (September - Page 72

Disable the setting of Quick Power-On Self Test from, BIOS Setup.

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

If a newly replaced FRU does not correct the problem: If you have reached this point of the check procedures and were instructed to replace a FRU but doing so did not correct the problem, reinstall the original FRU and go through "Start" again. If you want to print a copy of a BIOS Setup Utility screen to an attached printer, press Print Screen key, while the screen is displayed. PLEASE READ THE FOLLOWING: Human Error is a cause for concern when applied to check procedures. It exists in every first time set of analysis procedures. It is therefore essential for effective and time-efficient servicing that each stage of every procedure be verified. (For example: When a symptom is found, or when a symptom appears to have been cured; the preceding steps should be repeated for accuracy of analysis.) 001 - START To begin, note the following: q Disable the setting of "Quick Power-On Self Test" from BIOS Setup. q Disconnect all external cables and devices including speakers and microphone from the system unit, except for the keyboard, mouse, and monitor. q Power off the system unit before moving it or when replacing FRUs. q Remove all adapter cards, except for the factory-installed modem adapter card and any other IBM factory-installed adapter cards. q Disconnect any drives except: q 3.5-in. diskette drive q Hard disk drive q Factory-installed devices (such as a CD-ROM drive) q Make sure that all power cords and cables are connected properly. q Make sure that the monitor brightness and contrast controls are not turned down. q Power on the system unit. NOTE: Some monitors have a detachable system I/O signal cable between the monitor and the system unit. In this case, check this signal cable before replacing the unit. See "Monitor Port Signals" on page 136 for pin identification. 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
70
If a newly replaced FRU does not correct the problem:
If
you have reached this point of the check procedures and were
instructed to replace a FRU but doing so did not correct the
problem, reinstall the original FRU and go through "Start" again.
If you want to print a copy of a BIOS Setup Utility screen to an
attached printer, press
Print
Screen
key, while the screen is
displayed.
PLEASE READ THE FOLLOWING:
Human Error is a cause for concern when applied
to check procedures. It exists in every first time
set of analysis procedures. It is therefore
essential for effective and time-efficient servicing
that each stage of every procedure be verified.
(For example:
When a symptom is found, or
when a symptom appears to have been cured;
the preceding steps should be repeated for
accuracy of analysis.)
001 -
START
To begin, note the following:
q
Disable the setting of “Quick Power-On Self Test” from
BIOS Setup.
q
Disconnect all external cables and devices including
speakers and microphone from the system unit, except for
the keyboard, mouse, and monitor.
q
Power off the system unit before moving it or when
replacing FRUs.
q
Remove all adapter cards, except for the factory-installed
modem adapter card and any other IBM factory-installed
adapter cards.
q
Disconnect any drives except:
q
3.5-in. diskette drive
q
Hard disk drive
q
Factory-installed devices (such as a CD-ROM drive)
q
Make sure that all power cords and cables are connected
properly.
q
Make sure that the monitor brightness and contrast
controls are not turned down.
q
Power on the system unit.
NOTE:
Some monitors have a detachable system I/O signal
cable between the monitor and the system unit.
In
this case, check this signal cable before replacing the
unit. See “Monitor Port Signals” on page 136 for pin
identification.