Lenovo NetVista IBM PC300 (Type 2169) - Hardware Maintenance Manual (September - Page 91

IDE Secondary Channel Master and Slave Drives in BIOS

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

004 - IF THE NUMBER OF DISKETTE, HARD DISK, OR CD-ROM DRIVE IS NOT CORRECT, READ AHEAD; OR GO TO STEP 005. q Check the cable installation of all disk drives. q Diskette drive should be connected to the system board Floppy connector. (Please refer to the connectors and functions illustrated in chapter 5.) q IDE Primary Channel Master and Slave Drives in BIOS Setup should be connected to the system board primary IDE connector. (Please refer to the connectors and functions illustrated in chapter 5.) q IDE Secondary Channel Master and Slave Drives in BIOS Setup should be connected to the system board secondary IDE connector. (Please refer to the connectors and functions illustrated in chapter 5.) NOTE: The CD-ROM drive that comes with system unit should be configured as IDE Secondary Channel Master device. q Check the hard disk and CD-ROM drives jumper settings. See "3.5-In. Hard Disk Drive Jumper Locations" on page 133 and "CD-ROM Drive" on page 95. q Check the voltages of all disk drive power connectors. See "Power Supply Cable Connector Specifications" on page 129. q Correct the parameter settings under Disk Drives in the BIOS Setup. q In the BIOS Setup, check that the correct drive size is set for the flagged drive shown in the IDE sections of the Setuop utility.. q Load default settings. q If the problem remains, check the continuity on the drive and the cable and replace it if necessary. If that does not fix the problem, replace the system board. q End. 005 - q Select Diagnostics from the PC-Doctor diagnostics program main menu. Select and execute Floppy Disk Test if you want to test the diskette drive. Select and execute Hard Disk Test if you want to test the hard disk drive. q Select Interactive Tests from the PC-Doctor diagnostics program main menu, then select and execute CDROM/DVD Test if you want to test the CD-ROM drive. q If the diagnostics program did not detect a failure, but the system still displays a failure: 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
89
004 -
IF
THE
NUMBER
OF
DISKETTE, HARD DISK,
OR
CD-ROM DRIVE IS
NOT
CORRECT, READ AHEAD;
OR GO TO STEP 005.
q
Check the cable installation of all disk drives.
q
Diskette drive should be connected to the system board
Floppy connector. (Please refer to the connectors and
functions illustrated in chapter 5.)
q
IDE Primary Channel Master and Slave Drives in BIOS
Setup should be connected to the system board primary
IDE connector. (Please refer to the connectors and
functions illustrated in chapter 5.)
q
IDE Secondary Channel Master and Slave Drives in BIOS
Setup should be connected to the system board secondary
IDE connector. (Please refer to the connectors and
functions illustrated in chapter 5.)
NOTE:
The CD-ROM drive that comes with system unit
should be configured as IDE Secondary Channel
Master device.
q
Check the hard disk and CD-ROM drives jumper settings.
See “3.5-In. Hard Disk Drive Jumper Locations” on page
133 and "CD-ROM Drive" on page 95.
q
Check the voltages of all disk drive power connectors.
See “Power Supply Cable Connector Specifications” on
page 129.
q
Correct the parameter settings under Disk Drives in the
BIOS Setup.
q
In the BIOS Setup, check that the correct drive size is set
for the flagged drive shown in the IDE sections of the
Setuop utility..
q
Load default settings.
q
If the problem remains, check the continuity on the drive
and the cable and replace it if necessary. If that does not
fix the problem, replace the system board.
q
End.
005 –
q
Select
Diagnostics
from the PC-Doctor diagnostics
program main menu.
Select and execute
Floppy Disk
Test
if you want to test the diskette drive.
Select and
execute
Hard Disk Test
if you want to test the hard disk
drive.
q
Select
Interactive Tests
from the PC-Doctor diagnostics
program main menu, then select and execute
CD-
ROM/DVD Test
if you want to test the CD-ROM drive.
q
If the diagnostics program did not detect a failure, but the
system still displays a failure: