Lenovo PC 300PL Using your Personal Computer - PC300PL - 6592 - Page 52

Starting the Configuration/Setup Utility Program

Get Lenovo PC 300PL PDF manuals and user guides View all Lenovo PC 300PL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

ISA Legacy Resources shows which system resources (memory, I/O port, DMA, and interrupt) are used by ISA legacy adapters. You can view and change these settings. For information about required interrupt resource settings for ISA legacy adapters, refer to the documentation that comes with these adapters. Advanced Power Management contains settings that affect the energy-saving features of your computer, including the automatic power-on feature. You can view and change these settings. Important In most cases, when you add or remove hardware from your computer, the BIOS (basic input/output system) detects the changes and then updates the configuration automatically. Although the computer changes the configuration settings automatically, you must save these changes in the Configuration/Setup Utility program for the new configuration to take effect. If you do not save the new settings, your operating system will not start. To save the configuration after adding or removing hardware, complete the following steps. 1. When you turn on the computer, an error message indicating that a configuration change has occurred appears approximately 30 seconds after the memory-count numbers stop cycling in the top-left corner of the screen. When the configuration error message disappears, the POST Startup Errors screen appears, and you are prompted to Continue or Exit Setup. Select Continue. (If you select Exit Setup, you will get another error message.) 2. The Configuration/Setup Utility program menu appears with a right arrowhead ( ) next to the menu category in which the configuration change has occurred. Select this menu item if you want to view the new configuration settings, and then press Esc to return to the Configuration/Setup Utility program menu. 3. Select Save Settings from the Configuration/Setup Utility program menu. 4. Press Esc to exit the Configuration/Setup Utility program, and follow the instructions on the screen. Starting the Configuration/Setup Utility Program To start the Configuration/Setup Utility program: 1. Turn on your computer. If your PC is already on when you start this procedure, you must shut down the operating system, turn off the computer, wait a few seconds until all in-use lights go off, and restart the computer. (Do not use Ctrl+Alt+Del to restart the computer.) 38 Using Your Personal Computer

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
±
ISA Legacy Resources
shows which system resources (memory, I/O port,
DMA, and interrupt) are used by ISA legacy adapters.
You can view and
change these settings.
For information about required interrupt resource
settings for ISA legacy adapters, refer to the documentation that comes with
these adapters.
±
Advanced Power Management
contains settings that affect the energy-saving
features of your computer, including the automatic power-on feature.
You can
view and change these settings.
Important
In most cases, when you add or remove hardware from your computer, the
BIOS (basic input/output system) detects the changes and then updates the
configuration automatically.
Although the computer changes the configuration
settings automatically, you must
save
these changes in the Configuration/Setup
Utility program for the new configuration to take effect.
If you do not save the
new settings, your operating system will not start.
To save the configuration
after adding or removing hardware, complete the following steps.
1.
When you turn on the computer, an error message indicating that a
configuration change has occurred appears approximately 30 seconds after
the memory-count numbers stop cycling in the top-left corner of the screen.
When the configuration error message disappears, the POST Startup Errors
screen appears, and you are prompted to
Continue
or
Exit Setup
.
Select
Continue
.
(If you select
Exit Setup
, you will get another error message.)
2.
The Configuration/Setup Utility program menu appears with a right
arrowhead
(
²
)
next to the menu category in which the configuration change
has occurred.
Select this menu item if you want to view the new
configuration settings, and then press
Esc
to return to the
Configuration/Setup Utility program menu.
3. Select
Save Settings
from the Configuration/Setup Utility program menu.
4. Press
Esc
to exit the Configuration/Setup Utility program, and follow the
instructions on the screen.
Starting the Configuration/Setup Utility Program
To start the Configuration/Setup Utility program:
1.
Turn on your computer.
If your PC is already on when you start this
procedure, you must shut down the operating system, turn off the computer,
wait a few seconds until all in-use lights go off, and restart the computer.
(Do
not use
Ctrl+Alt+Del
to restart the computer.)
38
Using Your Personal Computer