Lenovo RS110 User Guide - Page 36

Installing, adapter

Get Lenovo RS110 - ThinkServer - 6438 PDF manuals and user guides
UPC - 884343312484
View all Lenovo RS110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

2. Turn off the server and all attached devices (see "Turning off the server" on page 9). 3. Disconnect all external cables and power cords. 4. Remove the server from the rack and place it on a flat, static-protective surface. 5. Press the cover-release button 1 . 6. Slide the cover back approximately 1.27 cm (0.5 inches); then, lift it off the server. Attention: For proper cooling and airflow, replace the cover before you turn on the server. Operating the server for extended periods of time (more than 30 minutes) with the cover removed might damage server components. Installing an adapter The following notes describe the types of adapters that the server supports and other information that you must consider when you install an adapter: v Locate the documentation that comes with the adapter and follow those instructions in addition to the instructions in this section. If you have to change switch settings or jumper settings on the adapter, follow the instructions that come with the adapter. v The adapter slots are on the riser-card assembly. You must first remove the riser-card assembly to access the adapter slots. v The two PCI Express slots on the riser-card assembly support PCI Express x8 1.0a adapters. v You can install one full-height three-quarter-length adapter in expansion slot 1 and one low-profile half-length adapter in expansion slot 2. Note: When the optional Remote Supervisor Adapter II SlimLine is installed in the server, you can install only a half-length adapter in expansion slot 1. v If you have installed an optional PCI-X riser-card assembly in the server, you can install a full-height, three-quarter-length PCI-X 64/133 MHz adapter in the PCI-X slot on the riser-card assembly. Note: When the optional Remote Supervisor Adapter II SlimLine is installed in the server, you can install only a half-length adapter in the PCI-X slot. v An optional Remote Supervisor Adapter II SlimLine can be installed only in the dedicated connector on the system board (see "System-board optional-device 22 ThinkServer RS110 Types 6435, 6436, 6437 and 6438: User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
2.
Turn
off
the
server
and
all
attached
devices
(see
“Turning
off
the
server”
on
page
9).
3.
Disconnect
all
external
cables
and
power
cords.
4.
Remove
the
server
from
the
rack
and
place
it
on
a
flat,
static-protective
surface.
5.
Press
the
cover-release
button
±1²
.
6.
Slide
the
cover
back
approximately
1.27
cm
(0.5
inches);
then,
lift
it
off
the
server.
Attention:
For
proper
cooling
and
airflow,
replace
the
cover
before
you
turn
on
the
server.
Operating
the
server
for
extended
periods
of
time
(more
than
30
minutes)
with
the
cover
removed
might
damage
server
components.
Installing
an
adapter
The
following
notes
describe
the
types
of
adapters
that
the
server
supports
and
other
information
that
you
must
consider
when
you
install
an
adapter:
v
Locate
the
documentation
that
comes
with
the
adapter
and
follow
those
instructions
in
addition
to
the
instructions
in
this
section.
If
you
have
to
change
switch
settings
or
jumper
settings
on
the
adapter,
follow
the
instructions
that
come
with
the
adapter.
v
The
adapter
slots
are
on
the
riser-card
assembly.
You
must
first
remove
the
riser-card
assembly
to
access
the
adapter
slots.
v
The
two
PCI
Express
slots
on
the
riser-card
assembly
support
PCI
Express
x8
1.0a
adapters.
v
You
can
install
one
full-height
three-quarter-length
adapter
in
expansion
slot
1
and
one
low-profile
half-length
adapter
in
expansion
slot
2.
Note:
When
the
optional
Remote
Supervisor
Adapter
II
SlimLine
is
installed
in
the
server,
you
can
install
only
a
half-length
adapter
in
expansion
slot
1.
v
If
you
have
installed
an
optional
PCI-X
riser-card
assembly
in
the
server,
you
can
install
a
full-height,
three-quarter-length
PCI-X
64/133
MHz
adapter
in
the
PCI-X
slot
on
the
riser-card
assembly.
Note:
When
the
optional
Remote
Supervisor
Adapter
II
SlimLine
is
installed
in
the
server,
you
can
install
only
a
half-length
adapter
in
the
PCI-X
slot.
v
An
optional
Remote
Supervisor
Adapter
II
SlimLine
can
be
installed
only
in
the
dedicated
connector
on
the
system
board
(see
“System-board
optional-device
22
ThinkServer
RS110
Types
6435,
6436,
6437
and
6438:
User
Guide