Lenovo RS110 User Guide - Page 40

Installing, drive, simple-swap, Serial

Get Lenovo RS110 - ThinkServer - 6438 PDF manuals and user guides
UPC - 884343312484
View all Lenovo RS110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

12. If the riser-card assembly is an optional PCI-X riser-card assembly in the server, reconnect the riser-card power cable to the riser-card assembly. 13. If you are installing a ServeRAID-MR10i controller (2.5-inch drive models only), complete the following steps: a. Disconnect the existing SAS/SATA controller signal cable from the hard disk drive backplane and from the controller; then, remove the cable from the server. b. Route the ServeRAID-MR10i signal cable as shown in the following illustration and connect it to the hard disk drive backplane. 1 RAID controller 2 Hard disc drive backplane 3 J9 4 J8 If you have other devices to install or remove, do so now. Otherwise, go to "Completing the installation" on page 35. Installing a hard disk drive Locate the documentation that comes with the hard disk drive and follow those instructions in addition to the instructions in this chapter. Attention: To avoid damage to the hard disk drive connectors, make sure that the cover is in place and fully closed whenever you install or remove a hard disk drive. Installing a simple-swap Serial ATA hard disk drive Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all power from the server before you remove or install a simple-swap hard disk drive. To install a simple-swap Serial ATA hard disk drive, complete the following steps. 26 ThinkServer RS110 Types 6435, 6436, 6437 and 6438: User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
12.
If
the
riser-card
assembly
is
an
optional
PCI-X
riser-card
assembly
in
the
server,
reconnect
the
riser-card
power
cable
to
the
riser-card
assembly.
13.
If
you
are
installing
a
ServeRAID-MR10i
controller
(2.5-inch
drive
models
only),
complete
the
following
steps:
a.
Disconnect
the
existing
SAS/SATA
controller
signal
cable
from
the
hard
disk
drive
backplane
and
from
the
controller;
then,
remove
the
cable
from
the
server.
b.
Route
the
ServeRAID-MR10i
signal
cable
as
shown
in
the
following
illustration
and
connect
it
to
the
hard
disk
drive
backplane.
±1²
RAID
controller
±3²
J9
±2²
Hard
disc
drive
backplane
±4²
J8
If
you
have
other
devices
to
install
or
remove,
do
so
now.
Otherwise,
go
to
“Completing
the
installation”
on
page
35.
Installing
a
hard
disk
drive
Locate
the
documentation
that
comes
with
the
hard
disk
drive
and
follow
those
instructions
in
addition
to
the
instructions
in
this
chapter.
Attention:
To
avoid
damage
to
the
hard
disk
drive
connectors,
make
sure
that
the
cover
is
in
place
and
fully
closed
whenever
you
install
or
remove
a
hard
disk
drive.
Installing
a
simple-swap
Serial
ATA
hard
disk
drive
Attention:
Simple-swap
hard
disk
drives
are
not
hot-swappable.
Disconnect
all
power
from
the
server
before
you
remove
or
install
a
simple-swap
hard
disk
drive.
To
install
a
simple-swap
Serial
ATA
hard
disk
drive,
complete
the
following
steps.
26
ThinkServer
RS110
Types
6435,
6436,
6437
and
6438:
User
Guide