Lenovo ThinkCentre Edge 72z Hardware Maintenance Manual (HMM) (May 2012) - Thi - Page 70

X-XXX 014-04X-XXX, Parallel port External Loopback failure

Get Lenovo ThinkCentre Edge 72z PDF manuals and user guides View all Lenovo ThinkCentre Edge 72z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Diagnostic Error Code FRU/Action 011-196-XXX Serial port test halt, error threshold exceeded 1. Press F3 to review the log file. 2. Restart the test to reset the log file. 011-197-XXX Serial port test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 53. 2. Re-run test 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 011-198-XXX Serial port test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6 "Using the Setup Utility program" on page 53. 2. Flash the system and re-test. See "Flash update procedures" on page 127. 3. Go to "Undetermined problems" on page 78. 011-199-XXX Serial port test failed, cause unknown 1. Go to "Undetermined problems" on page 78. 2. Flash the system and re-test. See "Flash update procedures" on page 127. 3. Replace component under function test. 011-2XX-XXX Serial port signal failure 1. External serial device 2. System board 014-000-XXX Parallel port Interface Test Passed No action 014-001-XXX Parallel port Presence 1. Remove external parallel device, if present. 2. Run the Setup Utility program, enable port 3. System board 014-002-XXX 014-003-XXX Parallel port Timeout/Parity error System board 014-013-XXX 014-014-XXX Parallel port Control Signal/Loopback test failure System board 014-015-XXX Parallel port External Loopback failure 1. Wrap plug 2. System board 014-027-XXX Parallel port Configuration/Setup error 1. Run the Setup Utility program, enable port 2. Flash the system. See "Flash update procedures" on page 127. 3. System board 014-03X-XXX 014-04X-XXX Parallel port failure System board 014-195-XXX Parallel port Test aborted by user Information only Restart the test, if necessary. 014-196-XXX Parallel port test halt, error threshold exceeded 1. Press F3 to review the log file. 2. Restart the test to reset the log file. 64 ThinkCentre Edge Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Diagnostic Error Code
FRU/Action
011-196-XXX
Serial port test halt, error threshold exceeded
1. Press F3 to review the log file.
2. Restart the test to reset the log file.
011-197-XXX
Serial port test warning
1. Make sure the component that is called out is
connected and/or enabled. See Chapter 6 “Using
the Setup Utility program” on page 53.
2. Re-run test
3. Replace the component that is called out in warning
statement.
4. Replace the component under test.
011-198-XXX
Serial port test aborted
1. If a component is called out, make sure it is
connected and/or enabled. See Chapter 6 “Using
the Setup Utility program” on page 53.
2. Flash the system and re-test. See “Flash update
procedures” on page 127.
3. Go to “Undetermined problems” on page 78.
011-199-XXX
Serial port test failed, cause unknown
1. Go to “Undetermined problems” on page 78.
2. Flash the system and re-test. See “Flash update
procedures” on page 127.
3. Replace component under function test.
011-2XX-XXX
Serial port signal failure
1. External serial device
2. System board
014-000-XXX
Parallel port Interface Test Passed
No action
014-001-XXX
Parallel port Presence
1. Remove external parallel device, if present.
2. Run the Setup Utility program, enable port
3. System board
014-002-XXX 014-003-XXX
Parallel port Timeout/Parity
error
System board
014-013-XXX 014-014-XXX
Parallel port Control
Signal/Loopback test failure
System board
014-015-XXX
Parallel port External Loopback failure
1. Wrap plug
2. System board
014-027-XXX
Parallel port Configuration/Setup error
1. Run the Setup Utility program, enable port
2. Flash the system. See “Flash update procedures”
on page 127.
3. System board
014-03X-XXX 014-04X-XXX
Parallel port failure
System board
014-195-XXX
Parallel port Test aborted by user
Information only Restart the test, if necessary.
014-196-XXX
Parallel port test halt, error threshold
exceeded
1. Press F3 to review the log file.
2. Restart the test to reset the log file.
64
ThinkCentre Edge Hardware Maintenance Manual