Lenovo ThinkPad Edge E125 (English) User Guide - Page 138

EMM386 Not Installed - Unable to Set Frame Base Address., C:\CONFIG.SYS

Page 138 highlights

Solution: The EEPROM checksum is not correct (block # 4 and 5). The system board should be replace, and the UUID needs to be reinstalled. Have the computer serviced. • Message: 0190: Critical low-battery error Solution: The computer turned off, because the battery is low. Connect the ac power adapter to the computer and charge the battery. • Message: 0191: System Security - Invalid remote change requested. Solution: The system configuration change has failed. Confirm the operation and try again. To clear the error, enter the ThinkPad Setup. • Message: 0199: System Security - Security password retry count exceeded. Solution: This message is displayed if you enter a wrong supervisor password more than three times. Confirm the supervisor password and try again. To clear the error, enter the ThinkPad Setup. • Message: 0251: System CMOS checksum bad Solution: The system CMOS might have been corrupted by an application program. The computer uses the default settings. Run ThinkPad Setup to reconfigure the settings. If you still see the same error code, have the computer serviced. • Message: 0253: EFI Variable Block Data was destroyed. Solution: The system EFI Variable Block Data might have been corrupted. The computer uses the default settings. Run ThinkPad Setup to reconfigure the settings. If you still see the same error code, have the computer serviced. • Message: 0271: Date and time error Solution: Neither the date nor the time is set in the computer. Set the date and time, using the ThinkPad Setup. • Message: 2000: ThinkVantage Active Protection sensor diagnostics failed. Solution: Have the computer serviced. • Message: 2100: Initialization error on HDD0 (Main HDD) Solution: The hard disk drive is not working. Have the hard disk drive serviced. • Message: 2110: Read error on HDD0 (Main HDD) Solution: The hard disk drive is not working. Have the hard disk drive serviced. • Message: 2200: Machine Type and Serial Number are invalid. Solution: POST warning message in case MTMSN is not set correctly. Have the computer serviced. • Message: 2201: Machine UUID is invalid. Solution: POST warning message in case UUID is not set correctly. Have the computer serviced. • Message: Fan error Solution: Cooling fan has failed. Have the computer serviced. • Message: EMM386 Not Installed - Unable to Set Page Frame Base Address. Solution: Edit C:\CONFIG.SYS and change a line from device = C:\WINDOWS\EMM386.EXE RAM to device = C:\WINDOWS\EMM386.EXE NOEMS and save this file. 122 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176

Solution
: The EEPROM checksum is not correct (block # 4 and 5). The system board should be replace,
and the UUID needs to be reinstalled. Have the computer serviced.
Message
: 0190: Critical low-battery error
Solution
: The computer turned off, because the battery is low. Connect the ac power adapter to the
computer and charge the battery.
Message
: 0191: System Security - Invalid remote change requested.
Solution
: The system configuration change has failed. Confirm the operation and try again. To clear
the error, enter the ThinkPad Setup.
Message
: 0199: System Security - Security password retry count exceeded.
Solution
: This message is displayed if you enter a wrong supervisor password more than three times.
Confirm the supervisor password and try again. To clear the error, enter the ThinkPad Setup.
Message
: 0251: System CMOS checksum bad
Solution
: The system CMOS might have been corrupted by an application program. The computer uses
the default settings. Run ThinkPad Setup to reconfigure the settings. If you still see the same error code,
have the computer serviced.
Message
: 0253: EFI Variable Block Data was destroyed.
Solution
: The system EFI Variable Block Data might have been corrupted. The computer uses the
default settings. Run ThinkPad Setup to reconfigure the settings. If you still see the same error code,
have the computer serviced.
Message
: 0271: Date and time error
Solution
: Neither the date nor the time is set in the computer. Set the date and time, using the ThinkPad
Setup.
Message
: 2000: ThinkVantage Active Protection sensor diagnostics failed.
Solution
: Have the computer serviced.
Message
: 2100: Initialization error on HDD0 (Main HDD)
Solution
: The hard disk drive is not working. Have the hard disk drive serviced.
Message
: 2110: Read error on HDD0 (Main HDD)
Solution
: The hard disk drive is not working. Have the hard disk drive serviced.
Message
: 2200: Machine Type and Serial Number are invalid.
Solution
: POST warning message in case MTMSN is not set correctly. Have the computer serviced.
Message
: 2201: Machine UUID is invalid.
Solution
: POST warning message in case UUID is not set correctly. Have the computer serviced.
Message
: Fan error
Solution
: Cooling fan has failed. Have the computer serviced.
Message
: EMM386 Not Installed - Unable to Set Page Frame Base Address.
Solution
: Edit
C:\CONFIG.SYS
and change a line from device =
C:\WINDOWS\EMM386.EXE RAM
to device =
C:\WINDOWS\EMM386.EXE NOEMS
and save this file.
122
User Guide