Home » Lexmark Manuals » Multifunction Devices » Lexmark 4600 » Manual Viewer

Lexmark 4600 T64x - Setup Guide - Page 15

Installing a duplex unit

Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

MFP Adjustable stand setup Installing a duplex unit The duplex unit attaches under the printer, below the standard tray and above any drawers. Note: Two optional duplex units are available. The 250-sheet duplex unit only works with printers that have a 250-sheet standard tray, and the 500-sheet duplex unit only works with printers that have a 500sheet standard tray. Make sure you have the appropriate duplex unit for the tray size installed in the printer. Place the duplex unit on top of any installed drawer or on the stand. Note: If you have a finisher or mailbox and do not have an optional drawer, the front edge of the duplex unit must be aligned with the front edge of the stand. The tab, round peg, and square hole on top of any drawer help you position the duplex unit so the edges are aligned properly. Make sure it is securely in place. Tab Square hole Round peg Installing a duplex unit 14

Section	Page
Stability Information	2
Getting started	10
Conventions	10
Using this book	10
Turning off the printer	10
Selecting a location for your printer and MFP	10
Customizing your MFP option	11
Drivers and options	12
Where to begin	12
MFP Adjustable stand setup	13
Assembling the MFP adjustable stand	13
Installing a 250- or 500-sheet drawer	14
Installing a duplex unit	15
Positioning the printer	16
Installing the finisher or mailbox	17
Installing the scanner	18
Low profile stand setup	19
Assembling the low profile stand	19
Installing a 250- or 500-sheet drawer	20
Installing a duplex unit	21
Positioning the printer	22
Installing the scanner shelf	23
Installing the scanner	24
Caster base setup	25
Installing the caster base	26
Installing the scanner shelf	26
Installing the scanner	27
Scanner stand setup	29
Positioning the scanner stand	29
Installing output options	30
Scanner option setup	31
Positioning the scanner	31
Setting up the printer	33
Removing the print cartridge packaging	33
Ordering print cartridges	34
Loading paper	36
Installing printer memory or option cards	37
Accessing the printer system board	37
Installing a memory card	39
Installing a firmware card	40
Installing an interfacecard and cable	41
Replacing the shield	42
Scanner setup	43
Installing the printer operator panel cover	43
Unlocking the scanner	44
Attaching cables and power cords	44
Installing drivers	45
Fax setup	46
Performing manual fax setup	46
Assigning a printer IP address	47
Verifying the IP settings	48
Performing browser fax setup	48
Verify MFP setup	49
Printing a menu settingspage	49
Printing the Help pages	49
Making a test copy	49
Sending a test fax	49
Testing a scan to PC profile	50
Distributing MFP user information	51
Finding user instructions	51
Distributing user information	51
Limiting MFP use	51
Solve setup problems	52

Match case Limit results 1 per page

Installing a duplex unit

MFP Adjustable stand setup

Installing a duplex unit

The duplex unit attaches under the printer, below the standard tray and above any drawers.

Note:

Two optional duplex units are available. The 250-sheet duplex unit only works with printers that have

a 250-sheet standard tray, and the 500-sheet duplex unit only works with printers that have a 500-

sheet standard tray. Make sure you have the appropriate duplex unit for the tray size installed in the

printer.

Place the duplex unit on top of any installed drawer or on the stand.

Note:

If you have a finisher or mailbox and do not have an optional drawer, the front edge of the duplex unit

must be aligned with the front edge of the stand.

The tab, round peg, and square hole on top of any drawer help you position the duplex unit so the edges are

aligned properly. Make sure it is securely in place.

Square hole

Tab

Round peg