Home » Lexmark Manuals » Printers » Lexmark Forms Printer 2590n » Manual Viewer

Lexmark Forms Printer 2590n Lexmark Forms Printer 2500+ Series User's Guide - Page 55

Emulation options, Interface options, IBM mode, Epson mode, OKI mode

View all Lexmark Forms Printer 2590n manuals

Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Understanding Setup mode and menu options 55 Emulation options Note: Use the Setup mode to configure the printer according to your needs. For more information, see "Using Setup mode" on page 48. To print a list of all default settings, press LineFeed from the Main menu. Make Emulation option selections from IBM (the factory default setting), Epson, or OKI mode. For more information regarding data stream changes, see the Technical Reference at www.lexmark.com. IBM mode Proprinter III, available only on 2580+ or 2581+ printers, enables compatibility with Proprinter III. • On-The printer emulates a Proprinter III. • Off-The printer operates with added capabilities. AGM, available only on 2590+ or 2591+ models, lets you use the high‑resolution 24‑wire graphics commands. These commands are similar to those used with the Epson LQ570 or LQ 1070. • On-Graphics commands are available. • Off-Graphics commands are not available. Note: Off is the factory default setting. Epson mode • Table Select-This lets you select Italic Character Table or Epson Extended Graphic Character Table. Note: Graphics is the factory default setting. • Int'l Char Set-This lets you select the character set associated with the language you want to print in. Notes: - Supported international character sets for Epson mode are: USA, France, Germany, U.K., Denmark, Sweden, Italy, and Spain I. - The following character sets are also supported, but only through host commands used by Epson FX850 or FX1050: Japan, Norway, Denmark II, Korea (2580+ or 2581+ models only), Spain II, Latin America, and Legal. - USA is the factory default setting. OKI mode OKI mode lets you select from the following functions: • 7 or 8 Bit Graphics • Paper Out Override • Reset Inhibit • Print Suppress Effective • Print DEL Code Interface options Note: Use Setup mode to configure the printer according to your needs. To print a list of all default settings, press LineFeed from the Main menu. The following list items outline and explain the Interface options and settings you can use with the printer:

Section	Page
Contents	2
Safety information	6
Learning about the printer	7
Printer overview	7
Applying control panel overlays	8
Understanding the printer features and functions	9
Printing a demonstration page	11
Printing a network setup page	13
Printing from Windows or DOS	13
Using IBM emulation mode	14
Using Epson emulation mode	14
Using Okidata MICROLINE emulation mode	15
Using the control panel	16
Understanding the control panel buttons	16
Understanding the control panel lights	18
Using the Start/Stop button	18
Setting the printer online or offline	19
Advancing paper	19
Using the Load/Unload function	20
Locking and unlocking the control panel	20
Selecting a Tractor mode	20
Selecting and locking a font	21
Disabling Font Lock	21
Selecting and locking a pitch	22
Disabling Pitch Lock	22
Loading paper	23
Setting the forms thickness lever	23
Paper paths	25
Using the Tear Off function	25
Loading continuous paper	26
Loading continuous forms using the push tractor	26
Front loading continuous forms using the pull tractor	29
Bottom loading continuous forms using the pull tractor	32
Loading cut forms	36
Loading a cut form or envelope manually	36
Aligning the left margin	39
Setting Top-Of-Form	40
Setting Top-Of-Form for continuous forms in push mode	40
Setting Top-Of-Form for continuous forms in pull mode	41
Setting Top-Of-Form for a cut form or an envelope	41
Setting Top-Of-Form in a macro	42
Paper and specialty media guide	43
Paper types and sizes supported by the printer	43
Changing tractor positions	44
Push tractor position	44
Pull tractor position	44
Converting the push tractor to pull tractor position	45
Converting the pull tractor to push tractor position	46
Understanding Setup mode and menu options	48
Using Setup mode	48
Changing menu settings (an example)	49
Setup Mode - Main menu	50
Main menu options	50
Forms Macro options	51
Data options	52
Control options	53
Emulation options	55
Interface options	55
Maintaining the printer	57
Ordering supplies	57
Removing the ribbon cartridge	57
Cleaning the printer	57
Recycling Lexmark products	58
Administrative support	59
Restoring the factory default settings	59
Supporting IPSec	60
Supporting SNMPv3	60
Using 802.1x authentication	61
Troubleshooting	62
Checking an unresponsive printer	62
Testing the printer	62
Checking the printer status	63
Adjusting character (bidirectional) alignment	65
Solving printing problems	67
Printer test works, but the printer does not print when attached to the computer	67
Printer is noisy	67
Printer sounds like it is printing, but does not print	67
Printer alarm sounds	67
Printer goes to the Tear Off position before the print job finishes	67
Buttons do not work, except for Start/Stop, FormFeed, Tear Off, and Load/Unload	68
Left margin moves to the right during printing	68
Incorrect line length; lines do not start at the left margin	68
Printer speed slows	68
Incorrect characters print, left margin changes, or printing stops	69
Printing continues beyond the edges of the continuous forms	69
Selected font or pitch is not printing or is changing	69
Solving paper feed problems	69
Paper is jammed in the printer	69
Paper is jammed in the Auto Sheet Feeder	70
Paper fed in the Auto Sheet Feeder jams at the printer entrance	70
Paper jam in the Tractor 2 Feeder	70
Printer does not feed paper	70
Printer does not feed from the optional Tractor 2 Feeder	71
Printer does not feed from the Auto Sheet Feeder	71
The optional Tractor 2 Feeder positions paper at incorrect Top-Of-Form position	71
The Auto Sheet Feeder feeds paper at an incorrect rate	71
The Auto Sheet Feeder places paper at the wrong Top-Of-Form position	72
Paper fed from the Auto Sheet Feeder is skewed	72
The Auto Sheet Feeder feeds multiple sheets	72
Solving print quality problems	73
Print is too light	73
Check the ribbon density control knob	73
Check the forms thickness lever	73
Dots are missing or print quality is poor	73
Characters are wrong or missing	74
Forms are smudged or print is too dark	74
Incorrect number of lines on a page	74
Graphics do not print	74
Incorrect line spacing or overprinting occurs	75
Contacting Customer Support	75
Notices	76
Edition notice	76
GOVERNMENT END USERS	77
Trademarks	77
Federal Communications Commission (FCC) compliance information statement	77
European Community (EC) directives conformity	78
Noise emission levels	78
Waste from Electrical and Electronic Equipment (WEEE) directive	78
ENERGY STAR	79
Power consumption	79
Product power consumption	79
Power Saver	79
Off mode	80
Total energy usage	80
STATEMENT OF LIMITED WARRANTY FOR LEXMARK LASER PRINTERS, LEXMARK LED PRINTERS, AND LEXMARK MULTIFUN ...	80

Match case Limit results 1 per page

Emulation options

Note:

Use the Setup mode to configure the printer according to your needs. For more information, see “Using Setup

mode” on page 48. To print a list of all default settings, press

LineFeed

from the Main menu.

Make Emulation option selections from IBM (the factory default setting), Epson, or OKI mode. For more information

regarding data stream changes, see the

Technical Reference

www.lexmark.com

IBM mode

Proprinter III, available only on 2580+ or 2581+ printers, enables compatibility with Proprinter III.

•

—The printer emulates a Proprinter III.

•

Off

—The printer operates with added capabilities.

AGM, available only on 2590+ or 2591+ models, lets you use the high

‑

resolution 24

‑

wire graphics commands. These

commands are similar to those used with the Epson LQ570 or LQ 1070.

•

—Graphics commands are available.

•

Off

—Graphics commands are not available.

Note:

Off is the factory default setting.

Epson mode

•

Table Select

—This lets you select Italic Character Table or Epson Extended Graphic Character Table.

Note:

Graphics is the factory default setting.

•

Int'l Char Set

—This lets you select the character set associated with the language you want to print in.

Notes:

–

Supported international character sets for Epson mode are: USA, France, Germany, U.K., Denmark, Sweden,

Italy, and Spain I.

–

The following character sets are also supported, but only through host commands used by Epson FX850 or

FX1050: Japan, Norway, Denmark II, Korea (2580+ or 2581+ models only), Spain II, Latin America, and Legal.

–

USA is the factory default setting.

OKI mode

OKI mode lets you select from the following functions:

•

7 or 8 Bit Graphics

•

Paper Out Override

•

Reset Inhibit

•

Print Suppress Effective

•

Print DEL Code

Interface options

Note:

Use Setup mode to configure the printer according to your needs. To print a list of all default settings, press

LineFeed

from the Main menu.

The following list items outline and explain the Interface options and settings you can use with the printer:

Understanding Setup mode and menu options