Marantz AV8003 AV8003 User Manua - Page 15

NAMES AND FUNCTION CONNECTIONS ENGLISH ABOUT BALANCED JACKS • The balanced output connector uses a XLR connector. • The XLR connector for professional use is internally wired in either of the following two systems. 1. European system (Pin w = HOT, Pin e = COLD) w q HOT e GND COLD 2. USA system (Pin w = COLD, Pin e = HOT) w COLD q e GND HOT • This unit uses the 1. European system. When a preamp or main amplifier adopting the European system is connected using a cable with XLR balanced connectors, the reproduced signal may be inverted of phase. CONNECTING AUDIO COMPONENTS CD recorder Analog Audio ANALOG ANALOG OUTPUT INPUT DIGITAL DIGITAL L L INPUT OUTPUT R R RL RL Digital Audio (coaxial) Digital Audio (optical) INPUT 1(TV) INPUT 2(DVD) FM (75Ω) GND AM ANTENNA INPUT 1(TV) COMPONENT Y CB/PB CR/PR VIDEO INPUT 3(VCR1) INPUT 2(DVD) INPUT 3(VCR1) INPUT 4(DSS/VCR2) Y CB/PB CR/PR Y INPUT 4(DSS / VCR2) OUTPUT 1 OUTPUT 2 OUT PUT 1 CB/PB CR/PR OUT PUT 2 TV(1) DVD(2) VCR1(3) DSS/VCR2(4) MONITOR ZONE OUT OUT TV(1) DVD(2) VCR1(3) IN OUT DSS/VCR2(4) IN OUT MONI. OUT VIDEO 4 5 IN OUT IN OUT REMOTE 6 COAX. IN 1 2 3 OPT. DIGITAL IN TV DVD DIGITAL OUT MAIN VCR1 DSS/VCR2 OUT ZONE TAPE L S-VIDEO DC OUT 1 1 IR FLASHER RECEIVER IN IN 2 CD/CDR 2 EMITTER OUT ZONE OUT CD/CDR BALANCED IN PUSH PUSH R L SL L SBL R IN OUT IN OUT IN OUT IN OUT A AUDIO B R SR (AUX) SBR RL RL LR LR Super Audio CD BALANCED LR UNBALANCED L R Analog Audio (balanced) Analog Audio (unbalanced) RL Or INPUT 1(TV) INPUT 2(DVD) FM (75Ω) GND AM ANTENNA COMPONENT Y CB/PB CR/PR VIDEO INPUT 3(VCR1) INPUT 2(DVD) INPUT 3(VCR1) INPUT 4(DSS/VCR2) Y CB/PB CR/PR Y INPUT 4(DSS / VCR2) OUTPUT 1 OUTPUT 2 OUT PUT 1 CB/PB CR/PR OUT PUT 2 R SR SBR SW L SL SBL R C VCR1(3) DSS/VCR2(4) MONITOR ZONE OUT OUT TV(1) DVD(2) VCR1(3) IN OUT DSS/VCR2(4) IN OUT MONI. OUT UNBALANCED SBR OUT IN OUT REMOTE COAX. IN OPT. DIGITAL OUT MAIN VCR1 DSS/VCR2 OUT ZONE TAPE S-VIDEO DC OUT 1 1 IR FLASHER RECEIVER IN IN 2 CD/CDR 2 EMITTER OUT ZONE OUT CD/CDR BALANCED IN CD/CDR IN PUSH PUSH CONNECTION 1 GND 2 1 2 HOT(+) 3 3 COLD(-) 3 2 1 R L SL 3 2 1 UNBALANCED BALANCED L SBL SELECTOR C RS-232C AC IN 7.1CH IN OUT IN OUT IN OUT IN OUT A AUDIO UNBALANCED BALANCED B R SR (AUX) SBR SW SELECTOR RL UNBALANCED BALANCED SELECTOR SETUP BASIC OPERATION ADVANCED OPERATION REMOTE CONTROLLER TROUBLESHOOTING 12 The output audio signal from the TAPE OUT jack and the CD/CD RECORDER OUT jack is the same signal which is currently selected. Caution: • Do not connect this unit and other components to mains power until all connections between components have been completed. Notes: • Insert all plugs and connectors securely. Incomplete connections may make noise. • Be sure to connect the left and right channels properly. Red connectors are for the R (right) channel, and white connectors are for the L (left) channel. • Be sure to connect input and output properly. • Refer to the instructions for each component that is connected to this unit. • Do not bind audio/video connection cables with power cords and speaker cables this will result in generating a hum or other noise. CONNECTING DIGITAL AUDIO COMPONENTS • There are 6 digital inputs, 3 coaxial jacks and 3 optical jacks, on the rear panel. You can use these jacks to input PCM, Dolby Digital and DTS bitstream signals from a CD, DVD, or other digital source components. • There is one digital output coaxial jack and one optical output jack on the rear panel. These jacks can be connected to a CD recorder, or a MD deck inputs, respectively. • Refer to the instructions for each component. To setup the digital audio format of DVD player, or other digital source's connected to digital input jacks. • Use fiber optical cables (optical) for DIG-1,2,3 input jacks. Use 75 ohms coaxial cables (for digital audio or video) for DIG-4, 5, 6 input jacks. • You can designate the input for each digital input/ output jacks according to your component. See page 24. Notes: • There is no Dolby Digital RF input jack. Use an external RF demodulator Dolby Digital decoder when connecting the Dolby Digital RF output jack of the videodisc player to the digital input jack. • The digital signal jacks on this unit conform to the EIA standard. If you use a cable that does not conform to this standard, this unit may not function properly. • Each type of audio jack works independently. Signals input through the digital and analog jacks are output through the corresponding digital and analog jacks, respectively. OTHERS