Marantz AV8003 AV8003 User Manua - Page 18

NAMES AND FUNCTION CONNECTIONS CONNECTING MULTI CHANNEL AUDIO COMPONENTS DVD Audio player or Super Audio CD Multi channel player CENTER L R FRONT SURR. SURR. SUB BACK WOOFER INPUT 1(TV) INPUT 2(DVD) CB/PB CR/PR INPUT 3(VCR1) INPUT 4(DSS/VCR2) Y CB/PB CR/PR Y INPUT 4(DSS / VCR2) OUTPUT 1 OUTPUT 2 OUT PUT 1 CB/PB CR/PR OUT PUT 2 R SR SBR SW L SL SBL C ZONE OUT TV(1) DVD(2) VCR1(3) IN OUT DSS/VCR2(4) IN OUT MONI. OUT UNBALANCED IN OUT TAPE S-VIDEO DC OUT 1 1 IR FLASHER RECEIVER IN IN 2 CD/CDR 2 EMITTER OUT ZONE OUT CD/CDR BALANCED IN PUSH PUSH CONNECTION 1 GND 2 1 2 HOT(+) 3 3 COLD(-) R L SL L SBL UNBALANCED BALANCED SELECTOR C RS-232C AC IN 7.1CH IN OUT IN OUT A AUDIO B R SR (AUX) SBR SW RL RL RL LR LRLR CONNECTING THE REMOTE CONTROL JACKS ENGLISH INPUT 1(TV) INPUT 2(DVD) FM (75Ω) GND AM ANTENNA INPUT 1(TV) COMPONENT Y CB/PB CR/PR VIDEO INPUT 3(VCR1) INPUT 2(DVD) INPUT 3(VCR1) INPUT 4(DSS/VCR2) Y CB/PB CR/PR Y INPUT 4(DSS / VCR2) OUTPUT 1 OUTPUT 2 OUT PUT 1 CB/PB OUT PUT 2 CR/PR TV(1) DVD(2) VCR1(3) DSS/VCR2(4) MONITOR ZONE OUT OUT TV(1) DVD(2) VCR1(3) IN OUT DSS/VCR2(4) IN OUT MONI. OUT 2 VIDEO IN OUT IN OUT S-VIDEO CD/CDR BALANCED IN REMOTE DC OUT PUSH PUSH 4 5 6 COAX. IN 1 1 IR FLASHER RECEIVER IN IN 1 2 3 OPT. 2 2 DIGITAL IN DIGITAL OUT OUT MAIN ZONE TV DVD VCR1 DSS/VCR2 TAPE CD/CDR EMITTER OUT ZONE OUT R L SL L SBL C L R IN OUT IN OUT IN OUT IN OUT A AUDIO B R SR (AUX) SBR SW OUT IN REMOTE CONTROL 1 MM8003 8CH POWER AMPLIFIER MM8003 STANDBY POWER ON/OFF REMOTE CONTROL IN OUT DVD player EXTERNAL INTERNAL RC OUT OPTION REMOTE CONTROL IN OUT CD player EXTERNAL INTERNAL SETUP BASIC OPERATION ADVANCED OPERATION REMOTE CONTROLLER TROUBLESHOOTING The 7.1CH INPUT jacks are for multichannel audio source such as a Super Audio CD multichannel player, DVD audio player or external decoder. If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page 24. q You can control other Marantz products through this unit with the remote controller by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote controller is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote control only at the unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier's, power switch is synchronized with this unit's power switch. To make REMOTE CONTROL connections with an MM8003, set P.AMPLINK to ENABLE. To make REMOTE CONTROL connections with another power amp, set P.AMPLINK to DISABLE. (See page 35) Set the REMOTE CONTROL SWITCH on the back of other units (not the AV8003) to "EXT." (EXTERNAL) to use this feature. w Whenever external infrared sensors or similar devices are connected to RC-5 IN of the unit, be sure to always disable operation of the infrared sensor on the unit by using the following procedure. 1. Hold down the ZONE button and the MENU button on the front panel at the same time for five seconds. 2. The setting "IR=ENABLE" is shown on the FL DISPLAY. 3. Press the CURSOR buttons (1, 2) to change this to "IR=DISABLE". 4. Press the ENTER button. Once this setting is made, the infrared sensor on the unit is disabled. Note: • Be sure to set to "IR=ENABLE" when external infrared sensors or similar devices are not connected. Otherwise, the unit will be unable to receive remote control commands. 5. To restore the original setting, perform steps 1 to 4 to set to "IR=ENABLE". 15 OTHERS