Marantz AV8003 AV8003 User Manua - Page 48

ENGLISH NAMES AND FUNCTION ADVANCED OPERATION DISPLAY MODE DISP DISPLAY RECORDING AN ANALOG SOURCE In normal operation, the audio or video source selected for listening through this unit is sent to the record outputs. This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT, CD/CDR OUT, VCR1 OUT, and DSS/VCR2 OUT in the record mode. SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT LISTENING THROUGH HEADPHONES This jack may be used to listen to the unit's output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phono plug. Note that the speakers will automatically be turned off when the headphone jack is in use. AV PRE TUNER AV8003 CONNECTIONS INPUT SELECTOR PURE DIRECT M-DAX AV PRE TUNER AV8003 UP HDMI DOWN VOLUME To record the input source signal you are currently watching or listening to PURE DIRECT H M-DAX INPUT SELECTOR SURROUND MODE AUTO ZONE ZONE SPEAKER MENU EXIT BAND T-MODE SETUP STANDBY POWER ON/OFF SURROUND MODE AUTO PURE DIRECT PHONES ZONE THX ZONE SPEAKER 7.1CH INPUT SETUP MIC MENU EXIT ENTER BAND T-MODE MEMORY CLEAR TOP M-DAX DISPLAY 1. PURE DIRECT AV PRE TUNER AV8003 UP HDMI If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source as following procedures. Switch the remote controller to AMP mode and press STANDBY POWER ON/OFF PURE DIRECT PHONES THX 7.1CH INPUT SETUP MIC ENTER TOP M-DAX BASIC OPERATION You can select the display mode for the front display of the unit. To select this mode, press the DISPLAY button on the front panel, or switch the remote controller to AMP mode and press the DISPLAY button. When this button is pressed, the display mode is switched in the following sequence. Input Mode → Surround Mode → Auto display OFF → Display OFF → Normal Mode → Input Mode STANDBY POWER ON/OFF INPUT SELECTOR M-DAX SURROUND MODE AUTO PURE DIRECT PHONES ZONE THX ZONE SPEAKER 7.1CH INPUT SETUP MIC 1. MENU EXIT BAND DOWN VOLUME T-MODE MEMORY CLEAR TOP M-DAX DISPLAY ENTER 1. To select the input source for recording, turn the INPUT FUNCTION SELECTOR knob on the front panel or press the HOME button and then the appropriate numeric buttons 1 through 9 on the remote controller. the < / > button until 002 is displayed. Then press the A/D button. When this button is pressed, the input mode is switched in the following sequence. Auto → HDMI → Digital → Analog → Auto Auto mode: The types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically. HDMI mode: Notes: • When using headphones, the surround mode will change to STEREO and Dolby Headphone by MENU and Cursor button. • The surround mode returns to the previous setting as soon as the headphone plug is removed from the jack. • The 7.1ch input mode returns to the previous setting as soon as the headphone plug is inserted to the jack. ADVANCED OPERATION REMOTE CONTROLLER Normal Mode: Displays the selected input function. If the function has been renamed using the Function Rename feature (see page 25), the renamed name appears on the display. Input Mode: Displays the input mode set via the Function Input Setup feature (see page 24). Surround Mode: Displays the status of the selected surround mode. Auto Display Off mode: The input source is now selected and you may watch or listen to it as desired. 2. The currently selected input source signal is output to the TAPE OUT, CD/CDR OUT, VCR1 OUT, and DSS/VCR2 OUT outputs for recording. 3. Start recording to the recording component as desired. Notes: • When connecting only digital signal input, output cannot be made to the TAPEOUT, CD/CDR OUT, HDMI mode can be selected only when an HDMI input has been assigned as an input source. When "HDMI AUDIO" under PREFERENCE of the SETUP MENU is set to "THROUGH", the HDMI mode cannot be selected. Digital mode: The input signal is fixed to an assigned digital input terminal. Analog mode: The analog input jacks are selected. This selection is temporary and will not be stored in memory. TROUBLESHOOTING The display is off. But, if you make a change to VCR1 OUT, or DSS/VCR2 OUT terminals. When To store changes to the input mode, select "1. INPUT the unit such as the input or surround mode, the display will show that change, then go back to off using recording functions, be sure to also make SETUP" from the MAIN MENU. (See page 24) connections for analog signal input. after about 3 seconds. • No conversion is made from Video signal input to Display Off mode: The display is off completely. Note: S-Video signal output or from S-Video signal input to Video signal output. Always use the same signal type for both input and output. • Video or audio signals input to HDMI input terminals • Only the DISP indicator will be illuminated on the cannot be recorded. front display in display off condition. OTHERS 45