Marantz AV8003 AV8003 User Manua - Page 50

NAMES AND FUNCTION CONNECTIONS SETUP BASIC OPERATION ENGLISH AUX INPUT TV AUTO ON/OFF FUNCTION LIP.SYNC DUAL BACKUP MEMORY If you don't need to connect 7.1 Ch. input terminals This function allows the component connected to the Depending on the image device (TV, monitor, The unit stores settings information in nonvolatile with multi channel decoder, TV-VIDEO in jack to control the power (ON/OFF) to projector, etc.) connected to the unit a time lag can memory even when the main power supply is turned L(front left) and R (front right) inputs terminals are the unit. occur between image signal processing and audio off. Using the Dual Backup Memory function, you available as AUX input. In this case, You can connect additional audio source to AUX as other audio input terminals. STANDBY POWER ON/OFF INPUT SELECTOR PURE DIRECT M-DAX AV PRE TUNER AV8003 UP HDMI DOWN VOLUME SURROUND MODE AUTO PURE DIRECT PHONES ZONE THX ZONE SPEAKER 7.1CH INPUT SETUP MIC MENU EXIT ENTER BAND T-MODE MEMORY CLEAR TOP M-DAX DISPLAY AUTO POWER ON 1. Be sure the TV auto mode is ENABLED. (Refer to page 34) 2. Connect your TV TUNER (etc) to the TV- VIDEO in terminal. Be sure to connect the VIDEO input. 3. Turn OFF the power to the TV TUNER and the unit. 4. Turn ON the TV TUNER and tune in a receivable station. 5. When the station is received, this unit turns ON and TV is selected automatically. signal processing. Though minor, this time lag can interfere with movie and music enjoyment. The LIP. SYNC feature delays the audio signal with respect to the image signal output from the unit to correct the time lag between the sound and image. It can be operated with the "LIP.SYNC" and 1 and 2 cursor buttons of the remote controller. To select Lip-sync mode, set the remote controller to the AMP mode, press the < / > button until 002 is displayed. Press the LIP. SYNC button. The initial setting is OFF (0 ms).The time lag can be adjusted in 10 ms steps up to 200 ms. Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag. can write settings information to another memory area to back up saved settings for recovery anytime as needed. BACKUP Set up the unit in the state for which you want to store the settings. Hold the MEMORY and ENTER buttons on the front panel simultaneously for at least 3 seconds. INPUT SELECTOR PURE DIRECT M-DAX AV PRE TUNER AV8003 UP HDMI DOWN VOLUME SURROUND MODE AUTO ZONE ZONE SPEAKER MENU EXIT BAND T-MODE MEMORY CLEAR To select AUX, turn the INPUT SELECTOR knob on the front panel, or press HOME button and press 6 AUTO POWER OFF STANDBY POWER ON/OFF PURE DIRECT PHONES THX 7.1CH INPUT SETUP MIC ENTER TOP M-DAX DISPLAY button on remote controller. 1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any VIDEO ON/OFF When no video signal is connected to the unit or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the "VIDEO OFF" setting. broadcast. 2. The power to the unit switches to STANDBY after approx. 5 minutes. Notes: • AUTO POWER OFF is canceled if this unit is set to a source other than TV. "MEMORY SAVING" is displayed and the unit's settings are saved. The stored settings information is retained until Dual Backup Memory is used again and the information is overwritten. MEMORY SAVING To select video off, switch the remote controller to AMP mode and press the < / > button until 004 is displayed. Then press the VIDEO OFF button. V-OFF PURE DIRECT M-DAX AV PRE TUNER AV8003 UP HDMI The function reactivates when TV is selected again. • Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON. • The S-Video terminal does not support "TV AUTO ON/OFF" function. • This function is inactive when STANDBY MODE is set to ECONOMY. To use this function, set STANDBY MODE to NORMAL. Note: • The LIP.SYSNC feature turns OFF (0 ms) in the SOURCE/PURE DIRECT mode. When the SOURCE/PURE DIRECT mode is deactivated, the set value of the LIP.SYSNC feature is automatically restored. Note: • The following settings values cannot be backed up. • Main Zone Volume • Zone Volume • Zone Speaker Volume INPUT SELECTOR DOWN VOLUME • Even if you do not correct the time lag manually this STANDBY POWER ON/OFF SURROUND MODE AUTO PURE DIRECT PHONES ZONE THX ZONE SPEAKER 7.1CH INPUT SETUP MIC MENU EXIT ENTER BAND T-MODE MEMORY CLEAR TOP M-DAX DISPLAY way, audio and video are automatically synchronized when the unit is connected to TV or Projector supporting Auto Lipsync Correction in HDMI 1.3a. For instructions on Auto Lipsync Correction, see page 35. The "V-OFF" indicator on the main unit display panel will light. ADVANCED OPERATION REMOTE CONTROLLER TROUBLESHOOTING OTHERS 47