Maytag MEDB800VQ Use and Care Guide - Page 27

Sensor Cycle Modifiers Use the DRYNESS LEVEl.button to select dryness levels for the Sensor Cycles. Press DRYNESS I.EVEI. until the desired Dryness setting illuminates. The preset dryness setting is Normal when a Sensor Cycle is selected. You can select a different Dryness I_evel, depending on your load, by pressing DRYNESS LEVEl_and choosing More, Normal, I_ess,or Damp. Selecting More, Normal, I.ess, or Damp automatically adjusts the Dryness I_evelat which the dryer will shut off. Once a Dryness I.evel is set, it cannot be changed without stopping the cycle. The initial preset temperature is the preferred setting for drying clothes; howeveB if desired, one alternate temperature may be selected to dry the load on a lower heat setting. Once the alternate temperature has been selected, the next time the same cycle is selected, the alternate temperature is remembered and displayed. The original (default) temperature may be reselected. The Delicate and Bulky cycles do not offer an alternate temperature. III damp lless m normal Imare III very dry dryn,ess ] adjust sensor cycle only NOTE: I)ryness Level selections cannot be used with the Timed or Steam Cycles. Timed Cycle Modifiers Use the TEMP LEVEl_ button to select temperatures for the Timed Cycles. Press TEMP I.EVEI.... until the desired temperature setting illuminates. air fluff a extra tow m low | medium I regular Air Fluff Use the Air Fluff Modifier for items that require drying without heat such as rubbeb plastic, and heat-sensitive fabrics. This table shows examples of items that can be dried using Air Huff. Type of Load Foam rubber - pillows, padded bras, stuffed toys Plastic - Shower curtains, tablecloths Rubber-backed rugs O[efin, po[ypropy[ene, sheer nylon Time* (Minutes) 20 - 30 20 - 30 40 - 50 10 - 20 *Reset cycle to complete drying, if needed. When using Air Fluff • Check that coverings are securely stitched. • Shake and fluff pillows by hand periodically during the cycle. • Dry item completely. Foam rubber pillows are slow to dry. NOTE: Air Fluff is not available with Sensor Cycles. You can customize your cycles by selecting options. options Drum Light On some models, select Drum I.ight to turn on the light inside the dryer drum. During a cycle, if Drum Light is selected, the drum light turns on and will remain on until DRUM LIGHT is pressed again, the door is opened and dosed, or the door is [eft open for 5 minutes. When the dryer is not running, the drum light will turn on when DRUM LIGHT is pressed or the dryer door is opened, and it will remain on until the dryer door has been open for 5 minutes, the dryer door is dosed, or DRUM I.IGHT is pressed again. Press DRUM I.IGHT at any time to turn the drum light ON or OFF. Wrinkle Prevent Plus Setting The Wrinkle Prevent Plus setting helps keep wrinkles from forming when you cannot unload the dryer promptly at the end of a cycle. During this option, the dryer stops tumbling and then tumbles again for a brief period. • Press WRINKI.E PREVENT PLUS setting to get up to 120 minutes of heat-free, periodic tumbling at the end of a cycle. Stop the Wrinkle Prevent Plus at any time by pressing WRINKI.E PREVENT PI.US setting or opening the dryer door. For the Wrinkle Control cycle, the Wrinkle Prevent Plus setting is preset to ON. The other Sensor Cycles will retain the Wrinkle Prevent Plus setting. For example, if you select the Wrinkle Prevent Plus setting in the Normal cycle, the Wrinkle Prevent Plus setting will be on the next time you select the Normal cycle. NOTE: If you do not select the Wrinkle Prevent Plus setting, the dryer stops after cool down. Damp Dry Signal Select the Damp Dry Signal to alert you that your clothes are approximately 80% dry. This is useful when you want to remove lightweight items in a mixed load to avoid overdrying or remove partially dry items that may need ironing. The Damp Dry Signal is useful when drying bedsheets/[inens in a mixed load. When the signal goes off, open the door to stop the dryer, rearrange the load inside the dryer, dose the door, and restart the dryer to finish the drying cycle. Rearranging the load will aid in the drying process. NOTE: The Damp Dry Signal is available only with the Sensor Cycles.