Maytag MEDB800VQ Use and Care Guide - Page 28
A. Dryer rack, B. Dryer back panel
UPC - 883049140506
View all Maytag MEDB800VQ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 28 highlights
l:i I'I A ° * _' End Signal The End Signal produces an audible sound when the drying cycle is finished. removing clothes at the end of the cycle reduces wrinkling. Press END SIGNAl. until the desired volume (High, I.ow, or Off) is selected. Promptly D nd signal 1 off.low.hi NOTE: When the Wrinkle Prevent Plus setting is selected and the End Signal is on, the tone will sound every 5 minutes until the clothes are removed, or the Wrinkle Prevent Plus setting ends. You can change Sensor and Timed Cycles, Modifiers, and Options anytime before pressing Start. • Three short tones sound if an unavailable combination is selected. The last selection will not be accepted. Changing Cycles after pressing Start 1. Press POWER/CANCEl ..... 2. Select the desired cycle and options. 3. Press START/PAUSE. The dryer starts at the beginning of the new cycle. NOTE: If you do not press Start/Pause within 5 minutes of selecting the cycle, the dryer automatically shuts off. Changing Modifiers and Options after pressing Start You can change an Option or Modifier anytime before the selected begins. 1. Press START/PAUSE. Option or Modifier 2. Select the new Option and/or Modifier. 3. Press START/PAUSE to continue the cycle. Changing the Preset Dryness Level Settings If all of your loads on all Sensor cycles are consistently not as dry as you would like, you may change the preset Dryness I.eve[ settings to increase the dryness. This change will affect all of your Sensor cycles. Your Dryness I.eve[ settings can be adjusted to adapt to different installations, environmental conditions, or personal preference. There are 3 drying settings: 1 (factory preset dryness [eve[), 2 (slightly dryer clothes, approximately 15% more drying time) and 3 (much dryer clothes, approximately 30% more drying time). 1. The Dryness I.eve[ settings cannot be changed while the dryer is running. 2. Press and hold the DRYNESS LEVEl_ button for 5 seconds. The dryer will beep, and "CF" will be displayed for 1 second followed by the current Dryness I_eve[ setting. 3. To select a new Dryness I_eve[ setting, press the DRYNESS I.EVEI. button again until the desired Dryness I.eve[ setting is shown. NOTE: While cycling through the settings, the current setting will not flash, but the other settings will flash. 28 4. Press START/PAUSE to save the Dryness I.evel setting. 5. The Dryness I.evel setting you selected will become your new preset Dryness I.evel setting for all Sensor cycles. Use the I)rying Rack to dry items such as sweaters and pillows without tumbling. The drum turns, but the drying rack does not move. If your model does not have a drying rack, you may be able to purchase one for your model. To find out whether your model allows drying rack usage and for information on ordering, please refer to the front page of the manual or contact the dealer from whom you purchased your dryer. NOTE: The drying rack must be removed for normal tumbling. I1o not use the automatic cycle with the drying rack. To use the drying rack 1. Open dryer door. ._%-g ).-_ 1:!;1.17 :-:i-> ,iIii_)i j_.._ 1_. -. oo/i A A. hont e_,e 2. Place drying rack inside dryer drum, positioning the back wire on the ledge of the inner dryer back panel. Push down on front edge of drying rack to secure at the front of the dryer. B A. Dryer rack hont edge B. Dryer back panel