Maytag MHWE300VW Use and Care Guide - Page 23

Chectkhefollowing: Isthepowecrordpluggeindtoagrounde3dprongoutlet? Is the washer door firmly closed? Has a cycle been selected, but START/PAUSE has not been selected and held for 1 second? Was the door open after completion of last cycle? Washer won't fill, wash, or rinse Check the following: Is the power cord plugged into a grounded 3 prong outlet? Is there power at the plug? Check electrical source or ca[[ an electrician. Are the hot and cold water faucets turned on? Is the water inlet hose kinked? Are the water inlet valve screens clogged? Turn off the water and remove inlet hoses from the washer. Remove any accumulated film or particles. Reinstall hoses, turn water on, and check for leaks. Washer stops • Check the following: Is the power cord plugged into a grounded 3 prong outlet? Is there power at the plug? Check electrical source or ca[[ an electrician. Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues, Are you using an extension cord? Do not use an extension cord. ca[[ an electrician. Washer won't drain or spin • Is the drain hose kinked? Is the drain hose clogged, or the end of the drain hose more than 96" (2.4 m) above the floor? • Is your voltage low? Check electrical source or call electrician. Do not use an extension cord. • Is the"SUD" routine active? Cycle will complete once extra suds are removed. • Is the load balanced? A single or bulky item may cause imbalance. Add more items or redistribute the load. Washer makes noise or vibrates Is the washer level? The washer must be [eve[. The four feet should be tightened against the washer cabinet. be properly installed, and the nuts should As water is drained from the washer, you may hear air being pulled through the pump. This happens during the end of draining. It is normal. Are you washing items with metal snaps, buckles, or zippers? You may hear metal items touching the washer drum. This is normal. Is washer installed on a sturdy and solid floor? Refer to the "Installation Instructions" for flooring requirements. Noise and vibration may be reduced by securing a piece of 3/4" (19.1 mm) plywood underneath your washer. The plywood may extend underneath both washer and dryer to keep them at equal heights. Washer leaks • Check household plumbing for leaks. • Are the inlet hose connections tight? For inlet hose connections, see "Connect the Inlet Hoses." Dispensers clogged or leaking • Are the laundry products in the correct dispenser compartment? Add the correct amounts of detergent, fabric softener, or liquid chlorine bleach to the correct compartments. • Is the detergent type selector in the correct position? Selector should be on the right for liquid detergent and to the [eft for powdered detergent. , Washer odor Z'I See "Cleaning Your Washer." Are you using HE detergent? Use of non-HE detergent can cause a film residue which can result in odor. Did you leave the door open after use? This washer has a tight sea[ to avoid water leaks. To avoid odors leave the door open to allow the washer to dry between uses. Load too wet Did you use the right cycle for the load being washed? Select a cycle with a higher spin speed. Did you wash a single item or bulky items or have you overloaded the washer? A single item, bulky items, or overloading may cause imbalance. Add items or try to evenly distribute your wet laundry in the drum, and start a Drain & Spin cycle. If the laundry is still wet, take haft of the load out of the washer and try again. NOTE: Use of the Max ExtractT M option is recommended excessive moisture at the end of the cycle. for heavy loads to avoid Residue or lint on load • Did you add detergent to the dispenser? For best results, add detergent to the Main wash compartment. the washer drum. I])o not add detergent to • Did you sort properly? Sort lint givers (towels, chenille) from lint takers (corduroy, synthetics). Also sort by color.