Maytag MMMF6030PZ Owners Manual - Page 13

3. Using a drill, cut out A & B & H & J holes, if the Wall studs do not located A & B hole, do not drill A & B hole, and follow the below instruction. In addition to being installed on at least 1 wall stud, the mounting plate must attach to the wall at both end holes. If the end holes are not over wall studs, use two 3/16-24 x 3" round head bolts with toggle nuts; if 1 end hole is over a wall stud, use 1 lag screw and one 3/16-24 x 3" round-head bolt with toggle nut; or if both end holes are over wall studs, use 2 lag screws. Following are 3 installation configurations. Installation for No Wall Studs at End Holes (Figures 1 and 2 in Find the wall Stud(s) section) 1. Drill 5/8" (1.6 cm) holes through the wall at both end holes marked in Step 3 of the "Mark Rear Wall". 2. Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the hole (s) marked in step 6 of the "Mark Rear Wall". Refer to figures 1 and 2 in "Possible Wall Stud Configurations" in the "Locate Wall Studs(s)" section. Installation for Wall Stud at One End Hole (Figure 3 in Find the wall Stud(s) section) 1. Drill a 3/16" (5 mm) hole into the wall stud at the end hole marked in Step 3 of the "Mark Rear Wall". 2. If installing on a second wall stud, drill a 3/16" (5 mm) hole into the wall stud at the other hole marked in Step 6 of the "Mark Rear Wall". Refer to Figure 3 in "Possible Wall Stud Configurations" in the "Locate all Stud(s)" section. 3. Drill a 5/8" (1.6 cm) hole through the wall at the other end. Installation for Wall Studs at Both End Holes (Figure 4 in Find the wall Stud(s) section) 1. Drill 3/16" (5 mm) holes into the studs at the end holes marked in Step 3 of the "Mark Rear Wall". 4. Using a keyhole saw, cut out the rectangular wall venting cutout area. Skip this step if for recirculation venting or roof venting installation. 6. Secure the mounting plate to the wall at both H & J holes using two 1/4 x 2" lag screws. A B A. Mounting Plate B. H & J holes No Wall Studs at End Holes (Figures 1 and 2 in Find the wall Stud(s) section) NOTE: The mounting plate must be secured to the wall on at least 1 wall stud as well as at both ends. 1. With the support tabs of the mounting plate facing forward, insert 3/16-24 x 3" round-head bolts through both end holes of mounting plate. 2. Start toggle nuts on bolts from the back of the mounting plate. Leave enough space for the toggle nuts to go through the wall and to open. B A C A A. Wall Venting Cutout Area Attach Mounting Plate to Wall 1. Position mounting plate on the wall. 2. Secure the mounting plate to the wall at both end holes drilled into the wall studs and/or drywall using either 3/16-24 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag screws. Refer to illustrations in "Possible Wall Stud Configurations" in the "Locate Wall Stud(s)" section, and the following sections "No Wall Studs at End Holes (Figures 1 and 2 in Find the wall Stud(s) section)" or " Wall Stud at One End Hole (Figure 3 in Find the wall Stud(s) section)" . 3. Insert lag screws into both end holes. 4. Check alignment of mounting plate, making sure it is level. 5. Secure the two end hole screws. A. 3/16-24 x 3" round-head bolt B. Mounting plate C. Spring toggle nut 3. Position mounting plate on the wall. 4. Push the 2 bolts with toggle nuts through the drywall, and finger tighten the bolts to make sure toggle nuts have opened against drywall. C A B D A. 3/16-24 x 3" round-head bolt B. Mounting plate C. Spring toggle nut D. Drywall 5. Insert lag screw(s) into the hole(s) drilled into wall stud(s) in Step 2 of "Installation for No Wall Studs at End Holes" in the "Drill Holes in Rear Wall" section. 13