Maytag MMMF6030PZ Owners Manual - Page 14

Rotate Blower Motor, Wall Stud at One End Hole in Find the, wall Studs

Get Maytag MMMF6030PZ PDF manuals and user guides View all Maytag MMMF6030PZ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

6. Check alignment of mounting plate, making sure it is level. 7. Securely tighten all lag screws and bolts. Wall Stud at One End Hole (Figure 3 in Find the wall Stud(s) section) 1. With the support tabs of the mounting plate facing forward, insert a 3/16-24 x 3" round-head bolt through the end hole that fits over the 5/8" (16 mm) hole drilled in step 3 of "Installation for Wall Stud at One End Hole" in the "Drill Holes in Rear Wall" section. 2. Start a toggle nut on the bolt from the back of the mounting plate. Leave enough space for the toggle nut to go through the wall and to open. 3. Position mounting plate on the wall. 4. Push the bolt with toggle nut through the drywall, and finger tighten the bolt to make sure toggle nut has opened against drywall. 5. Insert a lag screw into the remaining end hole. 6. If installing on a second wall stud, insert a lag screw into the other hole drilled in Step 2 of "Installation for Wall Stud at One End Hole" in the "Drill Holes in Rear Wall" section. 7. Check alignment of mounting plate, making sure it is level. 8. Securely tighten the lag screw(s) and bolt. Rotate Blower Motor This section include wall and roof venting installation, both venting installation need rotate blower motor, select one ventilation type before install the microwave oven. And follow the propriated instruction to rotate the blower motor. If for recirculation installation, no need to rotate the blower motor, this section can be skip. Rotate Blower Motor for Wall Venting Installation 1. Remove screw attaching damper plate to back of microwave oven, set the screw aside. 3. Remove 2 blower screws attaching blower motor to the microwave oven, and set aside. A A. Blower screws (in recessed holes) 4. Disconnect the blower motor wire from the connector. A B A A. Blower motor wire B. Connector 5. Lift blower motor out of microwave oven, and set aside. B A. Damper plate B. Screws 2. Turn and hold the damper plate vertically as shown. A A A. Damper plate 14 A. Blower motor

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
14
6.
Check alignment of mounting plate, making sure it is level.
7.
Securely tighten all lag screws and bolts.
Wall Stud at One End Hole (Figure 3 in Find the
wall Stud(s) section)
1.
With the support tabs of the mounting plate facing forward,
insert a 3/16-24 x 3" round-head bolt through the end hole that
fits over the 5/8" (16 mm) hole drilled in step 3 of “Installation
for Wall Stud at One End Hole” in the “Drill Holes in Rear Wall”
section.
2.
Start a toggle nut on the bolt from the back of the mounting
plate. Leave enough space for the toggle nut to go through the
wall and to open.
3.
Position mounting plate on the wall.
4.
Push the bolt with toggle nut through the drywall, and finger
tighten the bolt to make sure toggle nut has opened against
drywall.
5.
Insert a lag screw into the remaining end hole.
6.
If installing on a second wall stud, insert a lag screw into the
other hole drilled in Step 2 of “Installation for Wall Stud at One
End Hole” in the “Drill Holes in Rear Wall” section.
7.
Check alignment of mounting plate, making sure it is level.
8.
Securely tighten the lag screw(s) and bolt.
Rotate Blower Motor
This section include wall and roof venting installation, both venting
installation need rotate blower motor, select one ventilation type
before install the microwave oven. And follow the propriated
instruction to rotate the blower motor. If for recirculation
installation, no need to rotate the blower motor, this section can be
skip.
Rotate Blower Motor for Wall Venting Installation
1.
Remove
screw
attaching
damper
plate
to
back
of
microwave
oven,
set
the
screw
aside.
A.
Damper plate
B. Screws
2.
Turn and hold the damper plate vertically as shown.
A
A.
Damper plate
3.
Remove 2 blower screws attaching blower motor to the
microwave oven, and set aside.
A
A.
Blower screws (in recessed holes)
4.
Disconnect the blower motor wire from the connector.
A
B
A.
Blower motor wire
B.
Connector
5.
Lift blower motor out of microwave oven, and set aside.
A
A.
Blower motor
A
B