NEC V754Q Users Manual - English - Page 20

Connecting to a Personal Computer The type of video connections that can be used to connect to a computer depends on the computer's display adapter. The following table show the typical factory preset signal timing for each connection type. Some display cards may not be able to support the required resolution for proper image reproduction with the selected connection. The monitor will show the proper image by automatically adjusting the factory preset timing signal. Resolution 640 x 480 800 x 600 1024 x 768 1280 x 720 1280 x 768 1280 x 800 1280 x 1024 1360 x 768 1366 x 768 1400 x 1050 1440 x 900 1600 x 1200 1680 x 1050 1920 x 1080 1920 x 1200 1920 x 2160 3840 x 2160 3840 x 2160 3840 x 2160 3840 x 2160 4096 x 2160*3 4096 x 2160*3 Scanning frequency Horizontal Vertical 31.5 kHz 60 Hz 37.9 kHz 60 Hz 48.4 kHz 60 Hz 45.0 kHz 60 Hz 47.8 kHz 60 Hz 49.7 kHz 60 Hz 64 kHz 60 Hz 47.7 kHz 60 Hz 47.7 kHz 60 Hz 65.3 kHz 60 Hz 55.9 kHz 60 Hz 75.0 kHz 60 Hz 65.3 kHz 60 Hz 67.5 kHz 60 Hz 74.6 kHz 60 Hz 133.3 kHz 60 Hz 65.7 kHz 30 Hz 67.5 kHz 30 Hz 133.3 kHz 60 Hz 135.0 kHz 60 Hz 54.0 kHz 24 Hz 135.0 kHz 60 Hz *1: Recommended resolution. *2: Only HBR2 is set. *3: Compressed image. HDMI MODE1 MODE2 Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes Yes Yes No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No Yes*1 Yes No Yes No Yes*1 Yes Yes No Yes DisplayPort 1.1a 1.2 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes*1 Yes No No No Yes*1, *2 No No No No No No Connecting to a Player or Computer with HDMI • Please use an HDMI cable with the HDMI logo. • It may take a moment for the signal to appear after turning on the computer. • Some display cards or drivers may not display an image correctly. • When you use a computer with HDMI, please set OVER SCAN to "AUTO" or "OFF" as display drivers may not be fully compatible and may not display an image correctly (see page 34). • To output HDMI audio, set [HDMI1], [HDMI2] or [HDMI3] at AUDIO INPUT in the OSD or choose [HDMI1], [HDMI2] or [HDMI3] by pressing the remote control AUDIO INPUT button. • If the source signal is 3840 x 2160 (60 Hz) and 4096 x 2160 (60 Hz), please set MODE2 at HDMI in TERMINAL SETTINGS (See page 38). • If the monitor's main power is turned on after a connected computer is turned on, sometimes an image is not displayed. In this case, please turn off the computer then turn it on again. Connecting to a Computer with DisplayPort • Please use a DisplayPort cable with the DisplayPort compliance logo. • To use the DisplayPort out connector, please refer to Video out (See page 68). • It may take a moment for the signal to appear after turning on the computer. • When connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not appear. • Some DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock. • To output DisplayPort audio, set [DisplayPort1] or [DisplayPort2] at AUDIO INPUT in the OSD or choose [DisplayPort1] or [DisplayPort2] by the remote control AUDIO INPUT button. • To display individual images at each connected monitors with the DisplayPort OUT connector, please set DisplayPort1.2 and MST at DisplayPort in the TERMINAL SETTINGS (See page 38). • If the monitor's main power is turned on after a connected computer is turned on, sometimes an image is not displayed. In this case, please turn off the computer then turn it on again. English-18