NEC VT695 VT49/490/491/590/595/695 UM - Page 16

Battery Installation, Remote Control Precautions, Operating Range for Wireless Remote Control - take apart

Get NEC VT695 - XGA LCD Projector PDF manuals and user guides
UPC - 050927253607
View all NEC VT695 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Battery Installation 1 Press firmly and slide the battery cover off. 2 Install new batteries (AAA). Ensure that you have the batteries' polarity (+/-) aligned correctly. 1. Introduction 3 Slip the cover back over the bat- teries until it snaps into place. Do not mix different types of batteries or new and old batteries. Remote Control Precautions • Handle the remote control carefully. • If the remote control gets wet, wipe it dry immediately. • Avoid excessive heat and humidity. • Do not heat, take apart, or throw batteries into fire. • If you will not be using the remote control for a long time, remove the batteries. • Ensure that you have the batteries' polarity (+/-) aligned correctly. • Do not use new and old batteries together, or use different types of batteries together. • Dispose of used batteries according to your local regulations. Operating Range for Wireless Remote Control Remote sensor on projector cabinet 7m/22feet 30° 30° (*) 30° 30° AUTO ADJ. EXIT ON/STAND BY SOURCE SELECT MENU FOCUS ZOOM LAMP STATUS POWER ENTER 7m/22feet Remote control *NOTE: The VT590, VT490, VT59 and VT49 do not have the remote sensor on the rear panel. • The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of the remote sensor on the projector cabinet. • The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
8
1. Introduction
Remote Control Precautions
•
Handle the remote control carefully.
•
If the remote control gets wet, wipe it dry immediately.
•
Avoid excessive heat and humidity.
•
Do not heat, take apart, or throw batteries into fire.
•
If you will not be using the remote control for a long time, remove the batteries.
•
Ensure that you have the batteries
’
polarity (+/-) aligned correctly.
•
Do not use new and old batteries together, or use different types of batteries together.
•
Dispose of used batteries according to your local regulations.
Operating Range for Wireless Remote Control
1
Press firmly and slide the
battery cover off.
2
Install new batteries (AAA).
Ensure that you have the
batteries' polarity (+/
–
) aligned
correctly.
3
Slip the cover back over the bat-
teries until it snaps into place. Do
not mix different types of batter-
ies or new and old batteries.
•
The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of
the remote sensor on the projector cabinet.
•
The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls
on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
30
°
(
*
)
30
°
30
°
30
°
*NOTE: The VT590, VT490, VT59 and VT49 do not
have the remote sensor on the rear panel.
Battery Installation
7m/22feet
7m/22feet
Remote control
Remote sensor on projector cabinet