Onkyo TX-SR602 Owner Manual - Page 39

First Time Setup - microphone

Get Onkyo TX-SR602 PDF manuals and user guides View all Onkyo TX-SR602 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

59/3 @&OCPPL 1BHF  5VFTEBZ 4FQUFNCFS 1. First Time Setup This chapter explains the settings that you need to make before using the AV receiver. Automatic Speaker Setup 2 With the supplied speaker setup microphone, the Auto- matic Speaker Setup function can measure the test tone output by each speaker and automatically determine the number of speakers connected, their sizes, the distance from each speaker to the listening position, and so on. Before using this function, connect and position all your speakers. Put the speaker setup microphone in the listening position, and connect it to the SETUP MIC jack. MIC position 1 2 3-7 1 Turn on the AV receiver and the connected TV. On the TV, select the input to which the AV receiver is connected. Auto Speaker Setup Push Enter:Start Notes: • Wait at least five seconds after turn- ing on the AV receiver before plugging in the speaker setup microphone. • Make sure the microphone is horizontal. • If there's an obstacle between the microphone and any speaker, the automatic setup will not work correctly. Set the room how you would have it when enjoying a DVD. • If the AV receiver was previously muted, the Muting function will be cancelled. • The automatic setup cannot be used while a pair of headphones is connected. • By putting the microphone close to where your ears would normally be at the listening position, a more accurate setup can be achieved. If you use a tripod or level table, you can adjust the height of the microphone. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
39
First Time Setup
This chapter explains the settings that you need to make before using the AV receiver.
With the supplied speaker setup microphone, the Auto-
matic Speaker Setup function can measure the test tone
output by each speaker and automatically determine the
number of speakers connected, their sizes, the distance
from each speaker to the listening position, and so on.
Before using this function, connect and position all your
speakers.
Automatic Speaker Setup
1
Turn on the AV receiver and the
connected TV.
On the TV, select the input to which the
AV receiver is connected.
3–7
2
1
2
Put the speaker setup micro-
phone in the listening position,
and connect it to the SETUP MIC
jack.
Notes:
•
Wait at least five seconds after turn-
ing on the AV receiver before plug-
ging in the speaker setup
microphone.
•
Make sure the microphone is hori-
zontal.
•
If there’s an obstacle between the
microphone and any speaker, the
automatic setup will not work cor-
rectly. Set the room how you would
have it when enjoying a DVD.
•
If the AV receiver was previously
muted, the Muting function will be
cancelled.
•
The automatic setup cannot be used
while a pair of headphones is con-
nected.
•
By putting the microphone close to
where your ears would normally be
at the listening position, a more accu-
rate setup can be achieved. If you use
a tripod or level table, you can adjust
the height of the microphone.
MIC
position
Auto Speaker Setup
------------------------
Push Enter:Start
TX-NR702,602_En.book Page 39 Tuesday, September 7, 2004 1:18 PM