Onkyo TX-SR602 Owner Manual - Page 50

Speaker Level Calibration

Get Onkyo TX-SR602 PDF manuals and user guides View all Onkyo TX-SR602 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

@4FUVQ@&O 1BHF  5VFTEBZ 4FQUFNCFS 1. First Time Setup-Continued Speaker Level Calibration This setting is set automatically by the Automatic Speaker Setup function (see page 39). Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. Notes: • The speakers cannot be calibrated while the output of the AV receiver is muted, while a pair of headphones is connected, or when using the multichannel input. • Because the TX-SR702/702E supports THX, the test tone is output at the standard level of 0 dB (absolute volume setting 82). If you normally listen at volume settings below this, be careful because the test tone will be much louder. 1 2, 3 2-4 1, 6 1 RECEIVER Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen. 2 ENTER Use the Up and Down [ ]/[ ] buttons to select "2. Speaker Setup," and then press [ENTER]. The Speaker Setup menu appears. ENTER 50 3 ENTER ENTER 4 ENTER 5 6 Use the Up and Down [ ]/[ ] buttons to select "3. Level Calibration," and then press [ENTER]. The Level Calibration menu appears and the pink noise test tone is output by the front left speaker. Menu Ba2s.iScpeSaekteurpSetup 1-.-I-n-i-t-i-a-l--S-e-t-u-p---------- 2.12S.-pS34ep.aeLEkaeqekvureearlSieCCztoaeunlrpfiibSgreattionngs Ad34v..234--aSA...-ba-UnuuSLE-..-scrdpeq-CL-eerievu-ee-dooaea-nf-Sukll-tt-eSnAei-e-teddrCz-r-ttjae--iuSuDlr--Lnpesii--egttsbS--fsutre--tpaat--ntt--:cii-::-Meon--ang--ns-00-u-dd-a-BB-l---- 5.Lcai.sRtueg8nh0itHnzg Mode P:res0edtB 6.Pdbr.eSfu2er5rr0eHnRzcieght : 0dB ec.Su8r0r0HBzack R : 0dB fd.S2u.r5rkHBzack L : 0dB ge.Sur8rkHLzeft : 0dB h.Subwoofer : 0dB Note: Speakers that you set to No or None on the Speaker Configuration page (page 46) cannot be selected. Use the Up and Down [ ]/[ ] buttons to select each speaker, and use the Left and Right [ ]/ [ ] buttons to set the volume. The volume can be adjusted from -12 to +12 dB in 1 dB steps (-15 to +12 dB for the subwoofer). Repeat step 4 until the volume of the test tone from each speaker is the same. When using a handheld Sound Level Meter, calibrate each loudspeaker channel (Left, Center, Right, Right Surround, Surround Back Right, Surround Back Left, Left Surround, and Subwoofer) to 75 dB SPL at the listening position, measured with C-weighting and slow reading. Press the [SETUP] button. The setup menu closes. Notes: • This procedure can also be performed by using the remote controller. First press the [TEST TONE] button to output the test tone. Use the [LEVEL-] and [LEVEL+] buttons to set the volume, and use the [CH SEL] button to select the speakers.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
50
First Time Setup
—Continued
Speaker Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
Notes:
•
The speakers cannot be calibrated while the output of
the AV receiver is muted, while a pair of headphones
is connected, or when using the multichannel input.
•
Because the TX-SR702/702E supports THX, the
test tone is output at the standard level of 0 dB
(absolute volume setting 82). If you normally listen
at volume settings below this, be careful because
the test tone will be much louder.
Notes:
•
This procedure can also be performed by using the
remote controller. First press the [TEST TONE] but-
ton to output the test tone. Use the [LEVEL–] and
[LEVEL+] buttons to set the volume, and use the [CH
SEL] button to select the speakers.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “2. Speaker
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
This setting is set automatically by the Automatic
Speaker Setup function (see page 39).
1, 6
2–4
2, 3
1
RECEIVER
ENTER
ENTER
3
Use the Up and Down [
]/[
]
buttons to select “3. Level Cali-
bration,” and then press
[ENTER].
The Level Calibration menu appears
and the pink noise test tone is output by
the front left speaker.
Note:
Speakers that you set to No or None on
the Speaker Configuration page
(page 46) cannot be selected.
4
Use the Up and Down [
]/[
]
buttons to select each speaker,
and use the Left and Right [
]/
[
] buttons to set the volume.
The volume can be adjusted from –12
to +12 dB in 1 dB steps (–15 to +12 dB
for the subwoofer).
5
Repeat step 4 until the volume of
the test tone from each speaker
is the same.
When using a handheld Sound Level
Meter, calibrate each loudspeaker
channel (Left, Center, Right, Right Sur-
round, Surround Back Right, Surround
Back Left, Left Surround, and Sub-
woofer) to 75 dB SPL at the listening
position, measured with C-weighting
and slow reading.
6
Press the [SETUP] button.
The setup menu closes.
ENTER
ENTER
Menu
------------------------
2.Speaker Setup
------------------------
2-3.Level Calibration
------------------------
b.Center
:
0dB
c.Rught
:
0dB
d.Surr Right
:
0dB
e.Surr Back R
:
0dB
f.Surr Back L
:
0dB
g.Surr Left
:
0dB
h.Subwoofer
:
0dB
a.Left
:
0dB
ENTER
4_Setup_En Page 50 Tuesday, September 7, 2004 2:06 PM