Optoma WU1500 User manual - Page 57

maintenance, Replacing the lamp

Get Optoma WU1500 PDF manuals and user guides View all Optoma WU1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

maintenance Replacing the lamp 4 4 3 3 2 1 Procedure: 1. Switch off the power to the projector by pressing " " on the projector keypad or pressing " " on the remote control. 2. Set the Power switch to the "OFF" position. Allow the projector to cool down for at least 30 minutes. 3. Disconnect the power cord. 4. Unscrew the screws on the cover. 1 5. Open the cover. 2 6. Unscrew the screws on the lamp module(s). 3 7. Remove the lamp module(s) carefully. 4 8. To replace the lamp module(s), reverse the previous steps. 9. Turn on the projector and reset the lamp timer. 10. Lamp Reset: (i) Press "Menu"  (ii) Select "OPTION"  (iii) Select "Light Source Settings"  (iv) Select "Reset Light Source Hours"  (v) Select the desired option ("Lamp 1 Hours", "Lamp 2 Hours", or "Both"). Note: The screw on the lamp cover and the lamp cannot be removed. The projector cannot be turned on if the lamp cover has not been placed back on the projector. Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean the lamp module if it was accidentally touched. English 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
English
57
MAINTENANCE
Replacing the lamp
1
2
3
3
4
4
Procedure:
1.
Switch off the power to the projector by pressing “
” on the projector keypad or pressing “
” on the
remote control.
2.
Set the
Power
switch to the “OFF” position. Allow the projector to cool down for at least 30 minutes.
3.
Disconnect the power cord.
4.
Unscrew the screws on the cover.
1
5.
Open the cover.
2
6.
Unscrew the screws on the lamp module(s).
3
7.
Remove the lamp module(s) carefully.
4
8.
To replace the lamp module(s), reverse the previous steps.
9.
Turn on the projector and reset the lamp timer.
10.
Lamp Reset: (i) Press “Menu”
(ii) Select “OPTION”
(iii) Select “Light Source Settings”
(iv) Select “Reset Light Source Hours”
(v) Select the desired option (“Lamp 1 Hours”, “Lamp 2
Hours”, or “Both”).
Note:
±
The screw on the lamp cover and the lamp cannot be removed.
±
The projector cannot be turned on if the lamp cover has not been placed back on the projector.
±
Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean
the lamp module if it was accidentally touched.