Optoma WU1500 User manual - Page 72

Enable-->Side by Side., Other problems, Remote control problems

Get Optoma WU1500 PDF manuals and user guides View all Optoma WU1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

ADDITIONAL INFORMATION B lurry double image ‡‡ Select "PICTURE-->3D Display-->3D Enable-->Off" from the OSD to avoid normal 2D image is blurry double image. T wo images, side-by-side format ‡‡ Select "PICTURE-->3D Display-->3D Enable-->Side by Side" from the OSD for input signal is HDMI 1.3 2D 1080i side-by-side. I mage does not display in 3D ‡‡ Check if the battery of 3D glasses is drained. ‡‡ Check if the 3D glasses is turned on. ‡‡ When the input signal is HDMI 1.3 2D (1080i side-by-side half), select "PICTURE-->3D Display-->3D Enable-->Side by Side". Other problems T he projector stops responding to all controls ‡‡ If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. L amp burns out or makes a popping sound ‡‡ When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on page 57. Remote control problems If the remote control does not work ‡‡ Check the operating angle of the remote control is pointed within 23'(7m) ±40° (horizontally) or 23'(7m) ±15° (vertically) to the IR receivers on the projector. ‡‡ Make sure there are not any obstructions between the remote control and the projector. Move to within 10 m (32.8 ft) of the projector. ‡‡ Make sure batteries are inserted correctly. ‡‡ Replace batteries if they are exhausted. 72 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
English
72
ADDITIONAL INFORMATION
Blurry double image
±
Select “PICTURE-->3D Display-->3D Enable-->Off” from the OSD to avoid normal 2D image is blurry
double image.
Two images, side-by-side format
±
Select “PICTURE-->3D Display-->3D Enable-->Side by Side” from the OSD for input signal is
HDMI 1.3 2D 1080i side-by-side.
Image does not display in 3D
±
Check if the battery of 3D glasses is drained.
±
Check if the 3D glasses is turned on.
±
When the input signal is HDMI 1.3 2D (1080i side-by-side half), select “PICTURE-->3D Display-->3D
Enable-->Side by Side”.
Other problems
The projector stops responding to all controls
±
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Lamp burns out or makes a popping sound
±
When the lamp reaches its end of life, it will burn out and may make a loud popping sound.
If this
happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp,
follow the procedures in the “Replacing the Lamp” section on page 57.
Remote control problems
If the remote control does not work
±
Check the operating angle of the remote control is pointed within 23’(7m) ²40° (horizontally) or 23’(7m)
²15° (vertically) to the IR receivers on the projector.
±
Make sure there are not any obstructions between the remote control and the projector. Move to within
10 m (32.8 ft) of the projector.
±
Make sure batteries are inserted correctly.
±
Replace batteries if they are exhausted.