Panasonic AW-HE42 Operating Instructions - Page 145

flickering may be noticeable depending on the subject. This is, not a malfunction. If necessary

Get Panasonic AW-HE42 PDF manuals and user guides View all Panasonic AW-HE42 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 145 highlights

Troubleshooting (continued) Symptom Cause and remedial action The brightness changes cyclically or the colors change, and horizontal stripes can be seen passing across the screen ●● These phenomena (flicker) may occur under the illumination produced by fluorescent lighting, mercury bulbs or other types of discharge tubes. In cases like this, it is recommended that the electronic shutter speed be set as follows. When the Frequency is set to "59.94Hz" ●● Set to 1/100 in areas where the power line frequency is 50 Hz. ●● Set the electronic shutter to OFF in areas where the power line frequency is 60 Hz. When the Frequency is set to "50Hz" ●● Set to 1/120 in areas where the power line frequency is 60 Hz. ●● Set the electronic shutter to OFF in areas where the power line frequency is 50 Hz. This can also be resolved by setting the shutter mode to [Synchro] and adjusting the shutter value. Reference pages --- ●● This phenomenon occurs because the pixels are arranged When fine lines or cyclical patterns are shot, flickering is seen or coloring is added to them systematically on each image sensor. It is noticeable when the spatial frequency of a subject and the pixel pitch are brought into proximity so change the camera angle or take other such action. ●● When the high dynamic range function (HDR) is enabled, flickering may be noticeable depending on the subject. This is --- not a malfunction. If necessary, disable the HDR function. ●● Are the camera, switching hub, or other peripheral devices grounded? ●● Are power lines are running nearby? Noise occurs in the audio input ●● Is equipment generating strong electric or magnetic fields (e.g., television and radio antennas, air conditioning compressors, power transformers) located nearby? ---  If the noise is not reduced via movement of surrounding devices, use a microphone equipped with an amplifier, or connect an audio output with low output impedance. Tally lamp fails to light ●● Has "Disable" been selected for "Tally"?  When "Disable" is selected for "Tally", the camera's tally lamp will be off. Change the setting to "Enable". ●● Has "Off" been selected for "Record tally"?  When "Off" is selected for "Record tally", the unit's tally lamp does not light during recording to an SD card. Change the "Record tally" setting to "On". P.59, P.99 P.79 145

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
145
Symptom
Cause and remedial action
Reference pages
The brightness
changes cyclically or
the colors change, and
horizontal stripes can
be seen passing across
the screen
●
These phenomena (flicker) may occur under the illumination
produced by fluorescent lighting, mercury bulbs or other types
of discharge tubes.
In cases like this, it is recommended that the electronic shutter
speed be set as follows.
When the Frequency is set to “59.94Hz”
●
Set to 1/100 in areas where the power line frequency is 50 Hz.
●
Set the electronic shutter to OFF in areas where the power line
frequency is 60 Hz.
When the Frequency is set to “50Hz”
●
Set to 1/120 in areas where the power line frequency is 60 Hz.
●
Set the electronic shutter to OFF in areas where the power line
frequency is 50 Hz.
This can also be resolved by setting the shutter mode to
[Synchro] and adjusting the shutter value.
–––
When fine lines or
cyclical patterns are
shot, flickering is seen
or coloring is added to
them
●
This phenomenon occurs because the pixels are arranged
systematically on each image sensor. It is noticeable when the
spatial frequency of a subject and the pixel pitch are brought
into proximity so change the camera angle or take other such
action.
●
When the high dynamic range function (HDR) is enabled,
flickering may be noticeable depending on the subject. This is
not a malfunction. If necessary, disable the HDR function.
–––
Noise occurs in the
audio input
●
Are the camera, switching hub, or other peripheral devices
grounded?
●
Are power lines are running nearby?
●
Is equipment generating strong electric or magnetic fields (e.g.,
television and radio antennas, air conditioning compressors,
power transformers) located nearby?
If the noise is not reduced via movement of surrounding devices,
use a microphone equipped with an amplifier, or connect an audio
output with low output impedance.
–––
Tally lamp fails to light
●
Has “Disable” been selected for “Tally”?
When “Disable” is selected for “Tally”, the camera’s tally lamp will
be off. Change the setting to “Enable”.
P.59, P.99
●
Has “Off” been selected for “Record tally”?
When “Off” is selected for “Record tally”, the unit’s tally lamp does
not light during recording to an SD card. Change the “Record tally”
setting to “On”.
P.79
Troubleshooting
(continued)