Panasonic AW-HE42 Operating Instructions - Page 99

Tally, IR Control, Notes, IR ID, CAM/BAR, Bars Type, OSD Mix, OSD Off With Tally, OSD Status, Protocol

Get Panasonic AW-HE42 PDF manuals and user guides View all Panasonic AW-HE42 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

Web screen configurations (continued) Tally "Enable" or "Disable" is set here for the function which turns on or turns off the tally lamp using the tally control signal. Setting value: Disable, Enable Factory settings: Enable IR Control "Enable" or "Disable" is set here for operations conducted from the wireless remote control. The operations are enabled when the unit's power is turned on from an external device other than a wireless remote control, and they are disabled when the power is turned on from a wireless remote control. Setting value: Disable, Enable Factory settings: Enable Notes ●● At the point when this item's setting is changed, the new setting is not reflected in operation. It is reflected when the unit is set to standby mode and its power is turned on. ●● Follow one of the procedures below if the item's setting is changed by mistake and the unit can no longer be operated from a wireless remote control. When menu operations can be performed using another control device:  First change the item using a control device capable of performing menu operations, and then turn off the unit's power and turn it back on. When menu operations cannot be performed using other control devices: 1. Turn off the power of the units and devices that are connected. 2. Disconnect the unit's AC adaptor cable and LAN cable, and plug them back in. 3. Perform the operation for turning on the unit's power from the wireless remote control. 4. After changing this item, turn off the unit's power and turn it back on. IR ID Configure the unit's remote control ID. The settings for this item correspond to the [CAM1] to [CAM4] buttons on the wireless remote control. Setting value: CAM1, CAM2, CAM3, CAM4 Factory settings: CAM1 CAM/BAR Switch between color bar display and camera image display on the monitor and the web setup screen. Setting value: Camera, Colorbar Factory settings: Camera Note ●● When the color bar is displayed, a test tone (1 kHz) is output according to the Audio setting in the camera menu. Bars Type Change the type of color bar to display. (page 60) Setting value: Type1, Type2 Factory settings: Type2 Bars Title Set camera title (page 78) display to Off/On for when the color bar is displayed. Factory settings: Off Note ●● The camera title is not displayed when the camera's OSD menu is displayed in the Web screen. zzOSD Mix This item's setting is reflected when the [Set] button is pressed. OSD Off With Tally This is used to enable or disable the function for clearing the OSD menu displays when the tally signal is received by a command or contact. When the tally signal is released, the original OSD menu displays are restored. Factory settings: Off OSD Status "Off" or "On" is set here for the status display which appears during AWB operations. Factory settings: Off zzProtocol This item's setting is reflected when the [Set] button is pressed. Model Select Set the protocol model for standard serial communication. Do not select "Reserved1" to "Reserved7". Setting value: S EVIHD1, SBRC300, SBRCZ330, Reserved1 to 7 Factory settings: SEVIHD1 99

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
99
Web screen configurations
(continued)
Tally
“Enable” or “Disable” is set here for the function which
turns on or turns off the tally lamp using the tally control
signal.
Setting value:
Disable, Enable
Factory settings:
Enable
IR Control
“Enable” or “Disable” is set here for operations conducted
from the wireless remote control.
The operations are enabled when the unit’s power is
turned on from an external device other than a wireless
remote control, and they are disabled when the power is
turned on from a wireless remote control.
Setting value:
Disable, Enable
Factory settings:
Enable
●
At the point when this item’s setting is changed, the
new setting is not reflected in operation.
It is reflected when the unit is set to standby mode
and its power is turned on.
●
Follow one of the procedures below if the item’s
setting is changed by mistake and the unit can no
longer be operated from a wireless remote control.
When menu operations can be performed using
another control device:
First change the item using a control device
capable of performing menu operations, and then
turn off the unit’s power and turn it back on.
When menu operations cannot be performed
using other control devices:
1.
Turn off the power of the units and devices that
are connected.
2.
Disconnect the unit’s AC adaptor cable and
LAN cable, and plug them back in.
3.
Perform the operation for turning on the unit’s
power from the wireless remote control.
4.
After changing this item, turn off the unit’s
power and turn it back on.
Notes
IR ID
Configure the unit’s remote control ID.
The settings for this item correspond to the [CAM1] to
[CAM4] buttons on the wireless remote control.
Setting value:
CAM1, CAM2, CAM3, CAM4
Factory settings:
CAM1
CAM/BAR
Switch between color bar display and camera image
display on the monitor and the web setup screen.
Setting value:
Camera, Colorbar
Factory settings:
Camera
●
When the color bar is displayed, a test tone (1 kHz)
is output according to the Audio setting in the
camera menu.
Note
Bars Type
Change the type of color bar to display. (page 60)
Setting value:
Type1, Type2
Factory settings:
Type2
Bars Title
Set camera title (page 78) display to Off/On for when
the color bar is displayed.
Factory settings:
Off
●
The camera title is not displayed when the camera’s
OSD menu is displayed in the Web screen.
Note
z
OSD Mix
This item’s setting is reflected when the [Set] button is
pressed.
OSD Off With Tally
This is used to enable or disable the function for clearing
the OSD menu displays when the tally signal is received
by a command or contact.
When the tally signal is released, the original OSD menu
displays are restored.
Factory settings:
Off
OSD Status
“Off” or “On” is set here for the status display which
appears during AWB operations.
Factory settings:
Off
z
Protocol
This item’s setting is reflected when the [Set] button is
pressed.
Model Select
Set the protocol model for standard serial communication.
Do not select “Reserved1” to “Reserved7”.
Setting value:
SEVIHD1, SBRC300, SBRCZ330,
Reserved1 to 7
Factory settings:
SEVIHD1