Panasonic AW-UE4 Advanced Operating Instructions - Page 17

Refer to <Layout of wireless remote control signal light-sensing areas> on the below.

Get Panasonic AW-UE4 PDF manuals and user guides View all Panasonic AW-UE4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

1 11 HOME button 2 10 If you press and hold the button for 2 seconds, the zoom level of the unit is 3 changed to x1. 54 12 ZOOM button These are used to adjust the digital zoom. The zoom is adjusted in the wide-angle using the [W] button and in the 6 telephoto using the [T] button 13 FAST button Changes the pan/tilt or zoom speed to high speed. 7 11 8 12 9 13 Check out the following points before using the wireless remote control.  Point the wireless remote control at the unit's wireless remote control signal light‑sensing area (front side), and operate it within a range of 10 meters (32.8 ft.) from the area.  Refer to on the below.  The signal sensing distance is reduced if the angle at which the wireless remote control signals are sensed is increased. The light-sensing sensitivity is reduced to about one-half when the wireless remote control is pointed at an angle of 40 degrees from each position in front of a wireless remote control signal light-sensing area (front panel or back panel). If the remote control is operated from the behind the unit, it may be either difficult or impossible to perform the desired operations.  If the unit is installed near fluorescent lights, plasma monitors or other such products or if the unit is exposed to sunlight, the effects of the light may make it impossible for the unit to be operated using the wireless remote control. Be sure to follow the steps below for installation and use.  Take steps to ensure that the wireless remote control signal light- sensing area will not be exposed to the light from fluorescent lights, plasma monitors or other such products or from the sun.  Install the unit away from fluorescent lights, plasma monitors and other such products.  For about 10 minutes even after the batteries have been removed from the wireless remote control, the selection of the operation to be performed (the , , or button which was pressed last) will remain stored in the memory. When a longer period of time elapses, however, the selection is reset to the status established when the button was pressed. [Note] The arrows in the figure below show the light-sensing directions in which the wireless remote control signals travel. Wireless remote control signal light-sensing area(front side) 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
17
1
2
3
4
5
6
7
8
9
10
11
12
13
11
HOME button
If you press and hold the button for 2 seconds, the zoom level of the unit is
changed to x1.
12
ZOOM button
These are used to adjust the digital zoom.
The zoom is adjusted in the wide-angle using the [W] button and in the
telephoto using the [T] button
13
FAST button
Changes the pan/tilt or zoom speed to high speed.
Check out the following points before using the wireless remote control.
Point the wireless remote control at the unit’s wireless remote control signal light
‑
sensing area (front side),
and operate it within a range of 10 meters (32.8 ft.) from the area.
Refer to <Layout of wireless remote control signal light-sensing areas> on the below.
The signal sensing distance is reduced if the angle at which the wireless remote control signals are sensed
is increased.
The light-sensing sensitivity is reduced to about one-half when the wireless remote control is pointed at an angle of
40 degrees from each position in front of a wireless remote control signal light-sensing area (front panel or back
panel).
If the remote control is operated from the behind the unit, it may be either difficult or impossible to perform the
desired operations.
If the unit is installed near fluorescent lights, plasma monitors or other such products or if the unit is
exposed to sunlight, the effects of the light may make it impossible for the unit to be operated using the
wireless remote control.
Be sure to follow the steps below for installation and use.
Take steps to ensure that the wireless remote control signal light- sensing area will not be exposed to the light
from fluorescent lights, plasma monitors or other such products or from the sun.
Install the unit away from fluorescent lights, plasma monitors and other such products.
For about 10 minutes even after the batteries have been removed from the wireless remote control, the
selection of the operation to be performed (the <CAM1>, <CAM2>,
<CAM3> or <CAM4> button which was
pressed last) will remain stored in the memory.
When a longer period of time elapses, however, the selection is reset to the status established when
the <CAM1> button was pressed.
<Layout of wireless remote control signal light-sensing areas>
[Note] The arrows in the figure below show the light-sensing directions in which the wireless remote control signals
travel.
Wireless remote control signal
light-sensing area(front side)