Panasonic DP-190 Operating Instructions - Page 56

Troubleshooting, Check, Action

Get Panasonic DP-190 PDF manuals and user guides View all Panasonic DP-190 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Problem Solving Troubleshooting Check Unit Does Not Operate Does the display light? Does the Energy Saver key flash (or light) and the display is turned OFF? (See page 32) Does any of the U## codes and messages appear on the display? (U1, U13, U16....etc.) Does the Add Paper indicator and message appear on the display? Does the message and J## Codes appear on the display? (J00, J01, J02,...etc.) Does E#-## codes and messages appear on the display? The machine would not accept the next job during operation, instructed job would not be accepted for a long time period or job would not be completed. Light Copies Does the exposure indicator say "LIGHTER"? Does the Toner Cartridge replacement and message appear on the display? Action Check if the Power Switch (Main Power Switch on the Left Side of the machine) is turned ON and if the power cord is plugged into the AC outlet. Press Energy Saver key on the control panel. Perform actions in accordance with each message. Add paper. (See page 14) Remove the misfed paper. (See page 18) Be sure to set paper as adjusted with paper guides. (See page 42) Turn the Power Switch on the Left Side of the machine to the OFF* and ON position. If the error code does not clear, call your Service provider. Turn the Power Switch on the Left Side of the machine to the OFF* and ON position. NOTE: *If the Hard Disk Drive Unit (DA-HD19) is installed, see page 13. Press the DARKER Key. (See page 25) Replace the Toner Cartridge. (See page 16) 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
56
Problem Solving
Troubleshooting
Check
Action
Unit Does Not Operate
Check if the Power Switch (Main Power Switch
on the Left Side of the machine) is turned ON
and if the power cord is plugged into the AC
outlet.
Does the display light?
Press Energy Saver key on the control panel.
Does the Energy Saver key flash (or light)
and the display is turned OFF?
(See page 32)
Perform actions in accordance with each
message.
Does any of the U## codes and messages
appear on the display?
(U1, U13, U16
....
etc.)
Add paper. (See page 14)
Does the Add Paper indicator and message
appear on the display?
Remove the misfed paper. (See page 18)
Be sure to set paper as adjusted with paper
guides. (See page 42)
Does the message and J## Codes appear on
the display? (J00, J01, J02,...etc.)
Turn the Power Switch on the Left Side of the
machine to the OFF* and ON position. If the
error code does not clear, call your Service
provider.
Does E#-## codes and messages appear on
the display?
Turn the Power Switch on the Left Side of the
machine to the OFF
*
and ON position.
The machine would not accept the next job
during operation, instructed job would not be
accepted for a long time period or job would
not be completed.
Light Copies
Press the DARKER Key.
(See page 25)
Does the exposure indicator say
"LIGHTER"?
Replace the Toner Cartridge.
(See page 16)
Does the Toner Cartridge replacement and
message appear on the display?
NOTE:
*
If the Hard Disk Drive Unit (DA-HD19) is
installed, see page 13.