Panasonic SDRS100 Sd Movie Camera - Page 17

CHARGING THE BATTERY, Connect the AC adaptor supplied

Get Panasonic SDRS100 - SD MOVIE CAMERA PDF manuals and user guides View all Panasonic SDRS100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Charging the Battery When this unit is purchased, the battery is not charged. Charge the battery before using this unit. ¬ Set the power switch to [OFF]. (P18) B 1 2 DC IN 9.3V A 3 Connect the AC adaptor (supplied) A to this unit and the AC outlet. 1 Open this unit's terminal cover. 2 Connect the AC adaptor to this unit's DC input terminal [DC IN 9.3V]. 3 Connect the AC mains lead to the AC adaptor, then the AC outlet. The status indicator B starts blinking in red at intervals of about 2 seconds to signal that charging has commenced. Charging is completed when the lamp goes off. ≥ If the status indicator blinks faster or slower, refer to page 106. The AC Cable is for use with this unit only. Do not use it with other devices or use the AC Cable for other devices with this unit. ∫ Connecting to the AC outlet If you turn on this unit while charging the battery using the AC adaptor, you can use the power supplied from the AC outlet to power the unit for use. (While it is in use, the battery will not be charged.) ∫ Charging time and recordable time The times shown in the table below show the times at a temperature of 25 oC (77 oF) and a humidity of 60%. This is just a guide. If the temperature is higher or lower than the specified value, the charging time will become longer. ≥ The intermittent recordable time refers to recordable time when the recording and stopping operations are repeated. In reality, it may be shorter than this. Battery model number Voltage/ capacity Charging time Supplied battery/ CGA-S303 (optional) 7.4 V/ 760 mAh Approx. 1 h 30 min ≥ "1h 30 min" indicates 1 hour 30 minutes. Maximum continuously recordable time Intermittent recordable time Approx. 1 h 20 min Approx. 45 min ≥ The recordable time will become shorter when you use this unit with the LCD monitor lit up by pressing the [POWER LCD] button. ≥ The batteries heat up after use or charging. The unit and the SD card also heat up during use. This is not a malfunction. ≥ Along with the reduction of the battery capacity, the display will change: # # # # . If the battery discharges, then ( ) will flash. 17 VQT0T50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
17
VQT0T50
When this unit is purchased, the battery is not charged. Charge the battery before using this unit.
¬
Set the power switch to [OFF]. (P18)
Connect the AC adaptor (supplied)
A
to this unit and the AC outlet.
1
Open this unit’s terminal cover.
2
Connect the AC adaptor to this unit’s DC
input terminal [DC IN 9.3V].
3
Connect the AC mains lead to the AC
adaptor, then the AC outlet.
The status indicator
B
starts blinking in red at
intervals of about 2 seconds to signal that
charging has commenced. Charging is
completed when the lamp goes off.
≥
If the status indicator blinks faster or slower,
refer to page 106.
∫
Connecting to the AC outlet
If you turn on this unit while charging the battery using the AC adaptor, you can use the
power supplied from the AC outlet to power the unit for use. (While it is in use, the
battery will not be charged.)
∫
Charging time and recordable time
The times shown in the table below show the times at a temperature of 25
o
C (77
o
F)
and a humidity of 60%. This is just a guide. If the temperature is higher or lower than
the specified value, the charging time will become longer.
≥
The intermittent recordable time refers to recordable time when the recording and
stopping operations are repeated. In reality, it may be shorter than this.
≥
“1h 30 min” indicates 1 hour 30 minutes.
Charging the Battery
DC IN 9.3V
1
2
3
B
A
The
AC Cable
is for use with this unit only. Do
not use it with other devices or use the
AC
Cable
for other devices with this unit.
Battery model
number
Voltage/
capacity
Charging time
Maximum
continuously
recordable time
Intermittent
recordable time
Supplied battery/
CGA-S303
(optional)
7.4 V/
760 mAh
Approx.
1 h 30 min
Approx.
1 h 20 min
Approx.
45 min
≥
The recordable time will become shorter
when you use this unit with the LCD monitor lit
up by pressing the [POWER LCD] button.
≥
The batteries heat up after use or charging.
The unit and the SD card also heat up during
use. This is not a malfunction.
≥
Along with the reduction of the battery
capacity, the display will change:
#
#
#
#
. If the battery discharges,
then
(
) will flash.