Pioneer VSX-917V-S User Manual - Page 12

Connecting up, About the video converter - hdmi

Get Pioneer VSX-917V-S PDF manuals and user guides View all Pioneer VSX-917V-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

03 Connecting up About the video converter When the video converter is enabled, all analog video sources are output through all of the MONITOR VIDEO OUT jacks (HDMI and highdefinition progressive component video cannot be converted).1 See Digital Video Converter Setup on page 64 to switch the video converter on or off. If several video components are assigned to the same input function (see The Input Assign menu on page 61), the converter gives priority to component, S-video, then composite (in that order). This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Note 1 You must connect your monitor/TV to the receiver's HDMI/component video outputs when connecting these video sources. If the video signal does not appear on your TV or plasma display, try adjusting the resolution settings on your component or display. Note that some components (such as video game units) have resolutions that may not be converted. In this case, use an (analog) S-video or composite connection. 12 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Connecting up
03
12
En
About the video converter
When the video converter is enabled, all analog
video sources are output through all of the
MONITOR VIDEO OUT
jacks (HDMI and high-
definition progressive component video cannot
be converted).
1
See
Digital Video Converter
Setup
on page 64 to switch the video converter
on or off.
If several video components are assigned to
the same input function (see
The Input Assign
menu
on page 61), the converter gives priority
to component, S-video, then composite (in that
order).
Note
1
You must connect your monitor/TV to the receiver’s HDMI/component video outputs when connecting these video sources. If
the video signal does not appear on your TV or plasma display, try adjusting the resolution settings on your component or display.
Note that some components (such as video game units) have resolutions that may not be converted. In this case, use an (analog)
S-video or composite connection.
This product incorporates copyright protection technology
that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
consumer uses only unless otherwise authorized by
Macrovision. Reverse engineering or disassembly is
prohibited.