Pioneer XDV-P90 Owner's Manual - Page 75

MODE Switch Setting

Get Pioneer XDV-P90 - DVD Changer - External PDF manuals and user guides View all Pioneer XDV-P90 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Installation Note: • Before finally installing the unit, connect the wiring temporarily, making sure it is all connected up properly, and the unit and the system work properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. • Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop. • When mounting this unit, make sure none of the leads are trapped between this unit and the surrounding metalwork or fittings. • Do not mount this unit near the heater outlet, where it would be affected by heat, or near the doors, where rainwater might splash onto it. • Before drilling any mounting holes always check behind where you want to drill the holes. Do not drill into the gas line, brake line, electrical wiring or other important parts. • If this unit is installed in the passenger compartment, anchor it securely so it does not break free while the car is moving, and cause injury or an accident. • If this unit is installed under a front seat, make sure it does not obstruct seat movement. Route all leads and cords carefully around the sliding mechanism so they do not get caught or pinched in the mechanism and cause a short circuit. • Do not mount this unit on the spare tire board or any other unstable place. • Do not mount this unit anywhere that gets the sun and so becomes hot, like on the dashboard or the rear shelf. • Mount this unit on a flat surface. • Installations in other than the horizontal or vertical positions indicated will prevent this product from performing correctly or could cause malfunction. MODE Switch Setting Before installing, use a pen tip or other thin, pointed instrument to set the MODE Switch to the appropriate position for the component you are using it with. IP-BUS STAND ALONE Installation 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
72
Installation
Installation
Note:
•
Before finally installing the unit, connect the
wiring temporarily, making sure it is all con-
nected up properly, and the unit and the system
work properly.
•
Use only the parts included with the unit to
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.
•
Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
tions of the vehicle.
•
Install the unit where it does not get in the dri-
ver
’
s way and cannot injure the passenger if
there is a sudden stop, like an emergency stop.
•
When mounting this unit, make sure none of
the leads are trapped between this unit and the
surrounding metalwork or fittings.
•
Do not mount this unit near the heater outlet,
where it would be affected by heat, or near the
doors, where rainwater might splash onto it.
•
Before drilling any mounting holes always
check behind where you want to drill the holes.
Do not drill into the gas line, brake line, electri-
cal wiring or other important parts.
•
If this unit is installed in the passenger com-
partment, anchor it securely so it does not
break free while the car is moving, and cause
injury or an accident.
•
If this unit is installed under a front seat, make
sure it does not obstruct seat movement. Route
all leads and cords carefully around the sliding
mechanism so they do not get caught or
pinched in the mechanism and cause a short
circuit.
•
Do not mount this unit on the spare tire board
or any other unstable place.
•
Do not mount this unit anywhere that gets the
sun and so becomes hot, like on the dashboard
or the rear shelf.
•
Mount this unit on a flat surface.
•
Installations in other than the horizontal or ver-
tical positions indicated will prevent this prod-
uct from performing correctly or could cause
malfunction.
MODE Switch Setting
Before installing, use a pen tip or other thin,
pointed instrument to set the MODE Switch
to the appropriate position for the compo-
nent you are using it with.
STAND
ALONE
IP-BUS