Ridgid R4510 Operation Manual - Page 15

Assembling The Leg Stand - assembly

Get Ridgid R4510 PDF manuals and user guides View all Ridgid R4510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

ASSEMBLY ASSEMBLING THE LEG STAND See Figure 8. Many of the leg stand parts are movable. All hardware must be tightened securely but not so tight that the leg stand won't open and close. For easier assembly, match letter to letter and fingertighten all fasteners. Only tighten fasteners securely when you are sure the release lever locks over the stop pin.  Align handle with holes in the end of the upper tube and insert. Secure in place using a screw. Repeat for other side.  Place a carriage bolt through the center hole in the outer tubes then place a spacer on the bolt.  Slide the bolt/spacer into the inner leg assembly (A and C) and secure in place using a lock nut. Do not overtighten. Repeat for the other side.  Place the center brace on top of the inner leg assembly (curve side up) with the stop pin under the pedal assembly latch. NOTE: The stop pins rest on top of inner leg assembly.  Insert a carriage bolt through the top hole of the inner leg assembly then slide a spacer on the bolt. Repeat for the other side.  Slide the center brace onto the bolt and secure in place using a lock nut. Repeat for the other side.  With the curve handle turned downward, secure the upper tubes (D and F on the right side, and E and C on the left side) to the leg stand using carriage bolts, spacers, and lock nuts. The tube with the diverter valve attached should be placed on the left side of the leg stand.  Remove the lock nut and two flat washers from the axles on each side of the leg stand.  Slide the flat washer, wheel, and flat washer onto the axle through the hole in the center of the wheel. Secure in place using lock nut.  Repeat with the second wheel.  Before use, verify the release lever locks the leg stand securely. If the leg stand will not lock, do not use; contact an authorized service center for assistance. UPPER TUBE SMALL SPACER LOCK NUT CENTER BRACE LARGE SPACER CARRIAGE BOLT SCREW STOP PIN HANDLE OUTER TUBE WHEEL LOCK NUT INNER LEG ASSEMBLY FLAT WASHER, SMALL 15 AXLE FLAT WASHER, LARGE Fig. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
15
ASSEMBLING THE LEG STAND
See Figure 8.
Many of the leg stand parts are movable. All hardware must
be tightened securely but not so tight that the leg stand won’t
open and close. For easier assembly, match letter to letter
and fingertighten all fasteners. Only tighten fasteners securely
when you are sure the release lever locks over the stop pin.
Align handle with holes in the end of the upper tube and
insert. Secure in place using a screw. Repeat for other side.
Place a carriage bolt through the center hole in the outer
tubes then place a spacer on the bolt.
Slide the bolt/spacer into the inner leg assembly (A and C)
and secure in place using a lock nut. Do not overtighten.
Repeat for the other side.
Place the center brace on top of the inner leg assembly
(curve side up) with the stop pin under the pedal assembly
latch.
NOTE:
The stop pins rest on top of inner leg assembly.
ASSEMBLY
Fig. 8
SMALL
SPACER
LOCK
NUT
UPPER
TUBE
INNER LEG
ASSEMBLY
CENTER
BRACE
AXLE
LOCK
NUT
FLAT WASHER,
SMALL
STOP
PIN
WHEEL
OUTER
TUBE
CARRIAGE
BOLT
FLAT WASHER,
LARGE
Insert a carriage bolt through the top hole of the inner leg
assembly then slide a spacer on the bolt. Repeat for the
other side.
Slide the center brace onto the bolt and secure in place
using a lock nut. Repeat for the other side.
With the curve handle turned downward, secure the up-
per tubes (D and F on the right side, and E and C on the
left side) to the leg stand using carriage bolts, spacers,
and lock nuts. The tube with the diverter valve attached
should be placed on the left side of the leg stand.
Remove the lock nut and two flat washers from the axles
on each side of the leg stand.
Slide the flat washer, wheel, and flat washer onto the
axle through the hole in the center of the wheel. Secure
in place using lock nut.
Repeat with the second wheel.
Before use, verify the release lever locks the leg stand
securely. If the leg stand will not lock, do not use; contact
an authorized service center for assistance.
LARGE
SPACER
HANDLE
SCREW