Sanyo 24KHS72 Service Manual - Page 102

How to Install the Outdoor Unit

Get Sanyo 24KHS72 - 24,200 BTU Ductless Single Zone Mini-Split Wall-Mounted Heat Pump PDF manuals and user guides View all Sanyo 24KHS72 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

4. How to Install the Outdoor Unit First refer to Section 2. Installation Site Selection. 4-1. Wiring Instructions for the Outdoor Unit Regulations on wire size differ from locality to locality. For field wiring requirements, please refer to your local electrical codes. Make sure that the installation fully complies with all local and national regulations. (1) Remove access panel "C". (Fig. 46) (2) Connect the inter-unit and power supply line according to the drawing on the panel side. (3) Be sure to size each wire allowing approx. 4" (10 cm) longer than the required length for wiring. Store excess wiring inside the cabinet. (4) When connections are completed, check that all connections are correct as shown in the wiring system diagram on panel side. (5) Be sure to ground the unit according to your local codes. Lock nut Terminal block Conduit plate Plug Inter unit (Conduit) Cabinet Power supply (Conduit) Access panel C Fig. 46 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
16
4.
How to Install the Outdoor Unit
First refer to Section 2. Installation Site Selection.
4-1.
Wiring Instructions for the Outdoor Unit
Regulations on wire size differ from locality to locality. For
field wiring requirements, please refer to your local elec-
trical codes. Make sure that the installation fully complies
with all local and national regulations.
(1)
Remove access panel “C”. (Fig. 46)
(2)
Connect the inter-unit and power supply line accord-
ing to the drawing on the panel side.
(3)
Be sure to size each wire allowing approx. 4"
(10 cm) longer than the required length for wiring.
Store excess wiring inside the cabinet.
(4)
When connections are completed, check that all
connections are correct as shown in the wiring sys-
tem diagram on panel side.
(5)
Be sure to ground the unit according to your local
codes.
Lock
nu
t
Co
n
d
u
it
plate
Pl
ug
I
n
ter
un
it
(Co
n
d
u
it)
Power
su
pply
(Co
n
d
u
it)
Cabi
n
et
Termi
n
al
block
Acce
ss
pa
n
el
C
Fig. 46