Sony HT-X8500 Operating Instructions - Page 20

When the TV Remote Control does not Work, Remove WALL MOUNT TEMPLATE.

Get Sony HT-X8500 PDF manuals and user guides View all Sony HT-X8500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

3 Fasten the screws into the marks () on SCREW LINE () of WALL MOUNT TEMPLATE as in the illustration below. 228.5 mm 228.5 mm (9 in) (9 in) Screws Marks () When the TV Remote Control does not Work When the Sound Bar obstructs the remote control sensor of the TV, the TV remote control may not work. In that case, enable the IR repeater function of the Sound Bar. You can control the TV with the TV remote control by sending the remote signal from the rear of the Sound Bar. Press and hold STANDARD for 5 seconds to set the function to on or off. 10 mm to 11 mm (approx. 7/16 in) 4 Remove WALL MOUNT TEMPLATE. 5 Hang the Sound Bar on the screws. Align the holes of the rear of the Sound Bar with the screws, then hang the Sound Bar on the two screws. IR repeater on The HDMI and BLUETOOTH indicators flash. IR repeater off The Dolby ATMOS and DTS:X indicators flash. Notes • Be sure to check that the TV remote control cannot control the TV, and then set the IR repeater function to on. If it is set to on when the remote control can control the TV, appropriate operation may not be obtained because of the interference between the direct command from the remote control and the command via the Sound Bar. • If the IR repeater function is set to on, this function may not work depending on your TV. Also, the remote controls of other devices such as an air conditioner may not work correctly. In this case, change the installation position of the Sound Bar or TV. Note When sticking WALL MOUNT TEMPLATE, smooth it out fully. 20US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
20
US
3
Fasten the screws into the marks
(
) on SCREW LINE (
) of WALL
MOUNT TEMPLATE as in the
illustration below.
4
Remove WALL MOUNT TEMPLATE.
5
Hang the Sound Bar on the
screws.
Align the holes of the rear of the
Sound Bar with the screws, then
hang the Sound Bar on the two
screws.
When sticking WALL MOUNT TEMPLATE,
smooth it out fully.
When the TV Remote
Control does not Work
When the Sound Bar obstructs the
remote control sensor of the TV, the TV
remote control may not work. In that
case, enable the IR repeater function of
the Sound Bar.
You can control the TV with the TV
remote control by sending the remote
signal from the rear of the Sound Bar.
Press and hold STANDARD for 5
seconds to set the function to on or
off.
• Be sure to check that the TV remote
control cannot control the TV, and then
set the IR repeater function to on. If it is
set to on when the remote control can
control the TV, appropriate operation
may not be obtained because of the
interference between the direct
command from the remote control and
the command via the Sound Bar.
• If the IR repeater function is set to on, this
function may not work depending on
your TV. Also, the remote controls of
other devices such as an air conditioner
may not work correctly. In this case,
change the installation position of the
Sound Bar or TV.
Note
Screws
Marks (
)
10 mm to
11 mm
(approx.
7/16 in)
228.5 mm
(9 in)
228.5 mm
(9 in)
IR repeater on
The HDMI and BLUETOOTH indicators flash.
IR repeater off
The Dolby ATMOS and DTS:X indicators flash.
Notes