Stihl RE 110 PLUS Instruction Manual - Page 19

Save These, Instructions

Page 19 highlights

7 Before Starting Work - Do not allow the unit to be used or stored in freezing temperatures. - If the pressure washer must be transported or stored in freezing conditions, the pump must be filled with antifreeze to prevent cracking due to water expansion, @ 13.2. SAVE THESE INSTRUCTIONS! 7 Before Starting Work English 8 Assembling the Pressure Washer 8.1 Assembling Parts and Accessories WARNING To reduce the risk of severe injury from high-pressure spray, always switch off the pressure washer, shut off the water supply, relieve any remaining pressure in the system and lock the spray gun trigger before attempting to assemble the pressure washer or spray attachment. Bracket for Power Supply Cord 7.1 Preparing the Pressure Washer for Operation Before starting work: ► Place the pressure washer on flat and firm ground or other solid surface in an open area. ► Connect the spray gun and lance, @ 8.3. ► Insert the spray nozzle, @ 8.4. ► If desired, add detergent, @ 12.3. ► Connect the water supply, @ 9. ► Connect the power supply cord to a properly installed electrical outlet that matches the voltage and electrical frequency stated on the pressure washer's rating plate. Connect to an individual branch circuit only. ► Test the ground fault circuit interruptor (GFCI), @ 10.1 2 1 3 0000-GXX-B523 0458-620-8621-A ► Push the bracket (1) into the handle (2). ► Insert screws (3) into the handle and tighten. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80

0458-620-8621-A
17
English
7 Before Starting Work
SAVE THESE
INSTRUCTIONS!
7.1
Preparing the Pressure Washer for Operation
Before starting work:
Place the pressure washer on flat and firm ground or other
solid surface in an open area.
Connect the spray gun and lance,
@
8.3.
Insert the spray nozzle,
@
8.4.
If desired, add detergent,
@
12.3.
Connect the water supply,
@
9.
Connect the power supply cord to a properly installed
electrical outlet that matches the voltage and electrical
frequency stated on the pressure washer's rating plate.
Connect to an individual branch circuit only.
Test the ground fault circuit interruptor (GFCI),
@
10.1
8.1
Assembling Parts and Accessories
WARNING
To reduce the risk of severe injury from high-pressure spray,
always switch off the pressure washer, shut off the water
supply, relieve any remaining pressure in the system and
lock the spray gun trigger before attempting to assemble the
pressure washer or spray attachment.
Bracket for Power Supply Cord
Push the bracket (1) into the handle (2).
Insert screws (3) into the handle and tighten.
Do not allow the unit to be used or stored
in freezing temperatures.
If the pressure washer must be
transported or stored in freezing
conditions, the pump must be filled with
antifreeze to prevent cracking due to
water expansion,
@
13.2.
7
Before Starting Work
8
Assembling the Pressure Washer
0000-GXX-B523
2
1
3