Home » Stihl Manuals » Lawn & Garden » Stihl RE 110 PLUS » Manual Viewer

Stihl RE 110 PLUS Instruction Manual - Page 31

Transporting

Get Stihl RE 110 PLUS PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

14 Transporting ► Connect the power supply cord to a properly installed electrical outlet that matches the voltage and electrical frequency stated on the pressure washer's rating plate. ► Switch on the pressure washer and let the pump run for up to 30 seconds until the water flow stops. Remaining water will be eliminated from the system. ► Switch off the pressure washer and disconnect it from the power supply. NOTICE Freezing temperatures can damage components of the pressure washer. STIHL recommends storing the pressure washer indoors in a dry room where it is protected from freezing temperatures. Relieve all system pressure and make sure all water is eliminated from the pump system and hoses before storing. Protecting the Pressure Washer with Antifreeze WARNING When using antifreeze to protect your pressure washer in winter conditions, observe all warnings and instructions provided by the manufacturer to reduce the risk of environmental contamination or severe personal injury from ingestion. If the pressure washer is to be exposed to freezing temperatures, it should be protected by a glycol-based antifreeze. The antifreeze prevents water inside the pressure washer from freezing and causing damage to the pressure washer. To protect the pressure washer with antifreeze: ► Drain the water out of the high-pressure hose. ► Disconnect the spray lance from the spray gun. ► Connect the shortest possible water hose to the pressure washer. The shorter the water hose, the less antifreeze is needed. ► Point the spray lance downward and wait until all the water has flowed out of the system. ► Pour antifreeze into a clean container. English ► Connect a suction hose to the water inlet of the highpressure pump and place the other end of the hose in the container of antifreeze. ► Squeeze and hold the spray gun trigger. ► Switch on the pressure washer. ► Hold down the spray gun trigger until an even jet of antifreeze is delivered from the spray gun. Keep the spray gun in the container. ► Press and release spray gun trigger several times. ► Switch off the pressure washer and disconnect it from the power supply. ► Detach the spray gun, high-pressure hose and water hose and allow residual antifreeze to run into the container. ► Collect and dispose of the antifreeze in accordance with the manufacturer's specifications and all federal, state and local laws, regulations and ordinances. 14 Transporting 14.1 Transporting the Pressure Washer When transporting the pressure washer: 1 2 1 ► Pull the pressure washer by the pushbar (1), or carry the pressure washer by the pushbar (1) and carrying handle (2). 0000-GXX-4624-A0 0458-620-8621-A 29

Section	Page
1 Introduction	4
2 Guide to Using this Manual	4
2.1 Signal Words	4
2.2 Symbols in Text	5
3 Main Parts	6
3.1 Pressure Washer	6
3.2 Spray Attachment	7
4 Safety Symbols on the Product	7
4.1 Pressure Washer	7
5 IMPORTANT SAFETY INSTRUCTIONS	8
5.1 General Safety Warnings and Instructions	8
5.2 Intended Use	10
5.3 Operator	10
5.4 Personal Protective Equipment	11
5.5 Pressure Washer	11
5.6 Power Supply Cord	12
5.7 Connecting the Water Supply	13
5.8 Using the Pressure Washer	13
5.8.1 Before Operation	13
5.8.2 Holding and Controlling the Pressure Washer	14
5.8.3 Working Conditions	15
5.8.4 Operating Instructions	16
6 Maintenance, Repair and Storage	18
6.1 Warnings and Instructions	18
7 Before Starting Work	19
7.1 Preparing the Pressure Washer for Operation	19
8 Assembling the Pressure Washer	19
8.1 Assembling Parts and Accessories	19
8.2 Adjusting the Handle	20
8.2.1 Extending the Handle	20
8.2.2 Lowering the Handle	21
8.3 Spray Gun and Lance	21
8.3.1 Connecting the Spray Gun and Lance	21
8.3.2 Removing the Spray Gun and Lance	22
8.4 Inserting and Removing the Spray Nozzle	22
8.4.1 Inserting the Spray Nozzle	22
8.4.2 Removing the Spray Nozzle	23
9 Connecting the Water Supply	23
9.1 Connecting the Pressure Washer to the Mains Water Supply	23
10 Ground Fault Circuit Interruptor (GFCI)	24
10.1 Testing the GFCI	24
10.2 Resetting the GFCI	25
11 Switching the Pressure Washer On and Off	25
11.1 Switching On	25
11.2 Switching Off	26
12 During Operation	26
12.1 Unrolling the High-Pressure Hose	26
12.2 Activating and Locking the Spray Gun Trigger	26
12.3 Adding Detergents	27
12.4 Cleaning	28
13 After Finishing Work	29
13.1 Preparing for Transportation or Storage	29
13.2 Protecting the Pressure Washer in Winter Conditions	30
14 Transporting	31
14.1 Transporting the Pressure Washer	31
15 Storing	32
15.1 Storing the Pressure Washer	32
16 Cleaning	32
16.1 Cleaning the Pressure Washer	32
16.2 Cleaning the Nozzle and Spray Lance	32
16.3 Cleaning the Water Intake Screen	33
17 Inspection and Maintenance	34
17.1 Inspection and Maintenance Chart	34
17.2 Inspecting and Maintaining the Pressure Washer	35
17.3 Lubricating the Gaskets	35
18 Troubleshooting Guide	36
18.1 Pressure Washer	36
19 Specifications	38
19.1 STIHL RE 110 PLUS	38
19.2 Symbols on the Pressure Washer	38
19.3 Engineering Improvements	38
20 Replacement Parts and Equipment	39
20.1 Genuine STIHL Replacement Parts	39
21 Disposal	39
21.1 Disposal of the Pressure Washer	39
22 Limited Warranty	39
22.1 STIHL Incorporated Limited Warranty Policy	39
23 Trademarks	39
23.1 Registered Trademarks	39
23.2 Common Law Trademarks	39
24 Addresses	40
24.1 STIHL Incorporated	40
1 Introducción	42
2 Acerca de este manual de instrucciones	42
2.1 Palabras identificadoras	42
2.2 Símbolos en el texto	43
3 Componentes importantes	44
3.1 Hidrolavadora	44
3.2 Accesorio pulverizador	45
4 Símbolos de seguridad en el producto	45
4.1 Hidrolavadora	45
5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD	46
5.1 Advertencias e instrucciones generales sobre seguridad	46
5.2 Uso previsto	48
5.3 Operador	49
5.4 Equipos de protección personal	49
5.5 Hidrolavadora	50
5.6 Cordón eléctrico	50
5.7 Conexión del suministro de agua	51
5.8 Uso de la hidrolavadora	52
5.8.1 Antes del uso	52
5.8.2 Sujeción y control de la hidrolavadora	53
5.8.3 Condiciones de trabajo	54
5.8.4 Instrucciones de manejo	55
6 Mantenimiento, reparación y almacenamiento	56
6.1 Advertencias e instrucciones	56
7 Antes de empezar a trabajar	58
7.1 Preparación de la hidrolavadora para el funcionamiento	58
8 Armado de la hidrolavadora	58
8.1 Armado de las piezas y accesorios	58
8.2 Ajuste del mango	59
8.2.1 Extensión de el mango	59
8.2.2 Bajada del mango	60
8.3 Pistola rociadora y lanza	60
8.3.1 Conexión de la pistola rociadora y de la lanza	60
8.3.2 Retiro de la pistola rociadora y de la lanza	61
8.4 Inserción y retiro de la boquilla	61
8.4.1 Inserción de la boquilla	61
8.4.2 Retiro de la boquilla	62
9 Conexión del suministro de agua	62
9.1 Conexión de la hidrolavadora al suministro de agua	62
10 Interruptor de pérdidas a tierra (GFCI)	63
10.1 Pruebe el GFCI, .	63
10.2 Reposición del GFCI	64
11 Encendido y apagado de la hidrolavadora	64
11.1 Encendido	64
11.2 Apagado	65
12 Durante el funcionamiento	65
12.1 Desenrollado de la manguera de presión alta	65
12.2 Activación y bloqueo del gatillo de la pistola rociadora	65
12.3 Adición de detergentes	66
12.4 Limpieza	67
13 Después de completar el trabajo	68
13.1 Preparación para el transporte o el almacenamiento	68
13.2 Protección de la hidrolavadora en condiciones de invierno	69
14 Transporte	71
14.1 Transporte de la hidrolavadora	71
15 Almacenamiento	71
15.1 Almacenamiento de la hidrolavadora	71
16 Limpieza	71
16.1 Limpieza de la hidrolavadora	71
16.2 Limpieza de la boquilla y de la lanza rociadora	72
16.3 Limpieza de la malla de admisión de agua	72
17 Inspección y mantenimiento	73
17.1 Tabla de inspección y mantenimiento	73
17.2 Inspección y mantenimiento de la hidrolavadora	74
17.3 Lubricación de las empaquetaduras	74
18 Guía de solución de problemas	75
18.1 Hidrolavadora	75
19 Especificaciones	77
19.1 STIHL RE 110 PLUS	77
19.2 Símbolos en la hidrolavadora	77
19.3 Mejoramientos técnicos	77
20 Piezas y equipos de repuesto	78
20.1 Piezas de repuesto originales de STIHL	78
21 Eliminación	78
21.1 Desecho de la hidrolavadora	78
22 Garantía limitada	78
22.1 Política de garantía limitada de STIHL Incorporated	78
23 Marcas comerciales	78
23.1 Marcas comerciales registradas	78
23.2 Marcas comerciales por ley común	78
24 Direcciones	79

Match case Limit results 1 per page

0458-620-8621-A

English

14 Transporting

►

Connect the power supply cord to a properly installed

electrical outlet that matches the voltage and electrical

frequency stated on the pressure washer's rating plate.

►

Switch on the pressure washer and let the pump run for up

to 30 seconds until the water flow stops. Remaining water

will be eliminated from the system.

►

Switch off the pressure washer and disconnect it from the

power supply.

NOTICE

Freezing temperatures can damage components of the

pressure washer. STIHL recommends storing the pressure

washer indoors in a dry room where it is protected from

freezing temperatures. Relieve all system pressure and

make sure all water is eliminated from the pump system and

hoses before storing.

Protecting the Pressure Washer with Antifreeze

WARNING

When using antifreeze to protect your pressure washer in

winter conditions, observe all warnings and instructions

provided by the manufacturer to reduce the risk of

environmental contamination or severe personal injury from

ingestion.

If the pressure washer is to be exposed to freezing

temperatures, it should be protected by a glycol-based

antifreeze. The antifreeze prevents water inside the

pressure washer from freezing and causing damage to the

pressure washer.

To protect the pressure washer with antifreeze:

►

Drain the water out of the high-pressure hose.

►

Disconnect the spray lance from the spray gun.

►

Connect the shortest possible water hose to the pressure

washer. The shorter the water hose, the less antifreeze is

needed.

►

Point the spray lance downward and wait until all the water

has flowed out of the system.

►

Pour antifreeze into a clean container.

►

Connect a suction hose to the water inlet of the high-

pressure pump and place the other end of the hose in the

container of antifreeze.

►

Squeeze and hold the spray gun trigger.

►

Switch on the pressure washer.

►

Hold down the spray gun trigger until an even jet of

antifreeze is delivered from the spray gun. Keep the spray

gun in the container.

►

Press and release spray gun trigger several times.

►

Switch off the pressure washer and disconnect it from the

power supply.

►

Detach the spray gun, high-pressure hose and water hose

and allow residual antifreeze to run into the container.

►

Collect and dispose of the antifreeze in accordance with

the manufacturer's specifications and all federal, state

and local laws, regulations and ordinances.

14.1

Transporting the Pressure Washer

When transporting the pressure washer:

►

Pull the pressure washer by the pushbar (1), or carry the

pressure washer by the pushbar (1) and carrying

handle (2).

14 Transporting

0000-GXX-4624-A0