TP-Link TL-SC3230N TL-SC3230N V1 User Guide - Page 37

Setting, Network, PPPoE, User name, Password, IP address, Subnet mask, and Gateway read only, Status

Get TP-Link TL-SC3230N PDF manuals and user guides View all TP-Link TL-SC3230N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

6.1.5 PPPoE PPPoE: Stands for Point to Point Protocol over Ethernet A standard builds on Ethernet and Point-to-Point network protocol. It allows your camera with xDSL or cable connects with broadband network directly, then your camera can dial up and get a dynamic IP address. For more PPPoE and Internet configuration, please consult your dealer or ISP. The camera can directly connect to the xDSL, however, it should be set up on a LAN environment to program the PPPoE information first, and then connect to the xDSL modem. Power on again, then the camera will dial on to the ISP connect to the WAN through the xDSL modem. The procedures are • Connect to a LAN by DHCP or Fixed IP • Access the camera, and enter Setting Î Network Î PPPoE as below ¾ PPPoE: To enable or disable the PPPoE service here. ¾ User name: Type the user name for the PPPoE service which is provided by the ISP. ¾ Password: Type the password for the PPPoE service which is provided by the ISP. ¾ IP address, Subnet mask, and Gateway (read only): Shows the IP information got from PPPoE server site. ¾ Status: Shows the Status of PPPoE connection. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
29
6.1.5 PPPoE
PPPoE: Stands for Point to Point Protocol over Ethernet
A standard builds on Ethernet and Point-to-Point network protocol. It allows your camera with
xDSL or cable connects with broadband network directly, then your camera can dial up and get a
dynamic IP address. For more PPPoE and Internet configuration, please consult your dealer or
ISP.
The camera can directly connect to the xDSL, however, it should be set up on a LAN environment
to program the PPPoE information first, and then connect to the xDSL modem. Power on again,
then the camera will dial on to the ISP connect to the WAN through the xDSL modem.
The procedures are
• Connect to a LAN by DHCP or Fixed IP
• Access the camera, and enter
Setting
Î
Network
Î
PPPoE
as below
¾
PPPoE:
To enable or disable the PPPoE service here.
¾
User name:
Type the user name for the PPPoE service which is provided by the ISP.
¾
Password:
Type the password for the PPPoE service which is provided by the ISP.
¾
IP address, Subnet mask, and Gateway (read only):
Shows the IP information got from
PPPoE server site.
¾
Status:
Shows the Status of PPPoE connection.