Viper 5904 Owner Manual - Page 45

Remote Start Time-out Alert, Manual Transmission Start MTS mode - install manual

Get Viper 5904 PDF manuals and user guides View all Viper 5904 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

perature changes. If a change in temperature is detected this report will be sent to the remote for display. Each time the remote receives this report it will beep, update, and display the newest temperature information in the Status screen info center. Note Temperature report must be turned on by an authorized Directed dealer. Remote Start Time-out Alert During remote start a message is sent three minutes before and again at one minute before the engine turns off. The REMOTE START TIMEOUT IMMINENT animation and tones play as an alert to reset the runtime if desired. Manual Transmission Start (MTS mode) When installed into a manual transmission vehicle, the system requires that the MTS mode is properly set when parking. If MTS mode is not properly set or is defeated after being properly set the system will not start the engine and the REMOTE START NOT AVAILABLE screen and tones play as an alert. 1. With the engine running, set the parking brake and leave the engine running. For Pit Stop or Turbo Timer mode (to leave the engine running after arming) open the driver door. 2. Release the foot brake (if pressed during Step 1), or press and release the foot brake anytime. As long as the engine is running there is no time limit to perform this step. 3. Within 20 seconds of foot brake release, press any command button on the remote, after 20 seconds return to Step 2 (For Turbo Timer Mode, press the optional dash mounted activation button or send the Timer Mode command from the Advanced Start menu 42 © 2011 Directed Electronics. All rights reserved.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
42
© 2011 Directed Electronics. All rights reserved.
perature changes. If a change in temperature is detected this report
will be sent to the remote for display. Each time the remote receives
this report it will beep, update, and display the newest temperature
information in the Status screen info center.
Note
Temperature report must be turned on by an authorized Di-
rected dealer.
Remote Start Time-out Alert
During remote start a message is sent three minutes before
and again at one minute before the engine turns off. The
REMOTE START TIMEOUT IMMINENT
animation and tones play as an alert
to reset the runtime if desired.
Manual Transmission Start (MTS mode)
When installed into a manual transmission vehicle, the system requires
that the MTS mode is properly set when parking. If MTS mode is not
properly set or is defeated after being properly set the system will
not start the engine and the
REMOTE START NOT AVAILABLE
screen and
tones play as an alert.
1. With the engine running,
set
the parking brake and leave the
engine running. For Pit Stop or Turbo Timer mode (to leave the
engine running after arming)
open
the driver door.
2.
Release
the foot brake (if pressed during Step 1), or
press
and
release
the foot brake anytime. As long as the engine is running
there is no time limit to perform this step.
3.
Within 20 seconds of foot brake release,
press
any command
button on the remote, after 20 seconds return to Step 2 (For Turbo
Timer Mode, press the optional dash mounted activation button
or send the Timer Mode command from the Advanced Start menu