Vtech DS6771-3 User Manual - Page 58

manual, Registered, HANDSET, IN USE, ON / OFF, DS6771, battery

Page 58 highlights

I cannot dial out. Make sure there is a dial tone before dialing. It is normal if the handset takes a second or two to synchronize with the telephone base before producing a dial tone. Wait an extra second before dialing. Eliminate any background noise. Mute the handset before dialing, or dial from another room in your home with less background noise. The display shows To register HS... and ...see manual alternately. The handset does not work at all. The headset cannot pick up any call. It announces "Not registered". The handset is deregistered from the telephone base. Place the handset in the telephone base to register it back. The handset shows Registered and you hear a beep when the registration process completes. This process takes about 90 seconds to complete. The headset is deregistered from the telephone base. Follow the steps below to register it back. 1. Press and hold FIND HANDSET for four seconds. The IN USE light turns on. 2. Place the headset on the telephone base to register it back. During the registration process, the LED light flashes alternatively in red and blue, and turn red after the registration completes. This process takes about 60 seconds. Lift the headset, then press ON / OFF key on the headset. If you hear a dial tone, the registration is successful. I cannot add and connect my cell phone or headset to the telephone base. Make sure you have cellular coverage and the Bluetooth function of your cell phone or headset is turned on. See the user's manual of your cell phone or headset for more information. Make sure that the telephone base is in discoverable mode. Carefully follow the pairing instructions in this manual. Make sure that your Bluetooth cell phone or headset is not connected to any other Bluetooth device, and is connected to the telephone base and active on the device list. Turn off your cell phone or headset, and then turn it on again. The cell phone reception in my house is poor and I cannot connect it to my DS6771. The display shows Low battery. If there is a location in your house with better reception, you can leave your cell phone at that location while you use the DS6771 cell line. In order for this to work, the telephone base must be within 15 feet of the cell phone. Place the handset in the telephone base or charger for charging. The battery does not charge in the handset or the handset battery does not accept charge. Make sure the handset is placed in the telephone base or charger correctly. If the battery is completely depleted, charge the battery for at least 30 minutes before use. You may need to purchase a new battery. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72

52
I cannot dial
out.
Make sure there is a dial
tone before dialing. It is
normal if the handset
takes a second or two
to synchronize with the
telephone base before
producing a dial tone.
Wait an extra second
before dialing.
Eliminate any
background noise.
Mute the handset
before dialing, or dial
from another room in
your home with less
background noise.
The display
shows
To
register HS...
and
...see
manual
alternately. The
handset does
not work at all.
The handset is
deregistered from the
telephone base.
Place the handset in
the telephone base
to register it back.
The handset shows
Registered
and you
hear a beep when the
registration process
completes. This process
takes about 90 seconds
to complete.
The headset
cannot pick
up any call.
It announces
Not
registered”
.
The headset is
deregistered from the
telephone base. Follow
the steps below to
register it back.
1. Press and hold
FIND
HANDSET
for four
seconds. The
IN USE
light turns on.
2. Place the headset on
the telephone base to
register it back.
During the registration
process, the LED light
flashes alternatively in
red and blue, and turn
red after the registration
completes. This process
takes about 60 seconds.
Lift the headset, then
press
ON / OFF
key
on the headset. If you
hear a dial tone, the
registration is successful.
I cannot add
and connect
my cell phone
or headset to
the telephone
base.
Make sure you have
cellular coverage and the
Bluetooth function of your
cell phone or headset is
turned on. See the user’s
manual of your cell phone
or headset for more
information.
Make sure that the
telephone base is in
discoverable mode.
Carefully follow the pairing
instructions in this manual.
Make sure that your
Bluetooth cell phone or
headset is not connected
to any other Bluetooth
device, and is connected
to the telephone base and
active on the device list.
Turn off your cell phone or
headset, and then turn it
on again.
The cell phone
reception in my
house is poor
and I cannot
connect it to
my
DS6771
.
If there is a location in
your house with better
reception, you can leave
your cell phone at that
location while you use
the
DS6771
cell line. In
order for this to work, the
telephone base must be
within 15 feet of the cell
phone.
The display
shows
Low
battery
.
Place the handset in
the telephone base or
charger for charging.
The battery
does not
charge in the
handset or the
handset battery
does not
accept charge.
Make sure the handset is
placed in the telephone
base or charger correctly.
If the battery is
completely depleted,
charge the battery for at
least 30 minutes before
use.
You may need to
purchase a new battery.