Xerox Z750/N Setup Guide - Page 36

Troubleshooting

Get Xerox Z750/N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 042215455084
View all Xerox Z750/N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

EtherTalk and TokenTalk Configuration Troubleshooting If the printer is not in the Chooser, use the following troubleshooting procedure. 1. Check that the Configuration Page shows a printer name, a node number, and a zone. I If there is no node number, verify that the printer is properly cabled to the network. Test the cable segment by plugging in a new cable segment or using the cable segment of a printer that is in the Chooser. I If your network uses zones, and there is no zone name on the Configuration Page, or if the Configuration Page shows the wrong zone, see Changing the printer's EtherTalk/TokenTalk zone (optional) on page 30. Note The printer cannot create a zone; it must already exist. 2. If the Configuration Page shows the correct printer name, node number, and zone, and the printer is still not visible in the Chooser, check the following items: I If there is a Novell NetWare server on the network, verify that the NetWare server has been configured for AppleTalk Phase 2 routing and addressing. I If there is a Windows NT server on the network, verify that the printer has not been captured by a Windows NT machine. I If the printer continually reboots when connected to the network, it is possible that a router is broadcasting a zone of *, which is an invalid zone. I If using QuickDraw GX, the GX drivers must be installed. If you don't use QuickDraw GX, disable the QuickDraw GX, QuickDraw Helper, and ColorSync extensions. Networking Setup Guide 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
Networking Setup Guide
31
EtherTalk and TokenTalk Configuration
Troubleshooting
If the printer is not in the
Chooser,
use the following troubleshooting procedure.
1.
Check that the Configuration Page shows a printer name, a node number, and a zone.
■
If there is no node number, verify that the printer is properly cabled to the
network.
Test the cable segment by plugging in a new cable segment or using the
cable segment of a printer that is in the
Chooser.
■
If your network uses zones, and there is no zone name on the Configuration Page,
or if the Configuration Page shows the wrong zone, see
Changing the printer’s
EtherTalk/TokenTalk zone (optional)
on page 30.
2.
If the Configuration Page shows the correct printer name, node number, and zone,
and the printer is still not visible in the
Chooser,
check the following items:
■
If there is a Novell NetWare server on the network, verify that the NetWare server
has been configured for AppleTalk Phase 2 routing and addressing.
■
If there is a Windows NT server on the network, verify that the printer has not
been captured by a Windows NT machine.
■
If the printer continually reboots when connected to the network, it is possible
that a router is broadcasting a zone of
*,
which is an invalid zone.
■
If using QuickDraw GX, the GX drivers must be installed. If you don't use
QuickDraw GX, disable the QuickDraw GX, QuickDraw Helper, and ColorSync
extensions.
Note
The printer cannot create a zone; it must already exist.