Yamaha CP50 Owner's Manual - Page 28

Select PreAmp, ModFx, PwrAmp, Reverb Sw., Speed, Select assign, ble k, L1-Rel, L1-Dm, R Time

Get Yamaha CP50 PDF manuals and user guides
UPC - 086792936963
View all Yamaha CP50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Using Performances 2 Press and hold the [STORE/ASSIGN] button (for at least one second). You will be asked to select a block, and the lamps to the top-left of the [PRE-AMP], [MOD-FX], [PWR-AMP] (CP5 only), and [REVERB] buttons will start to flash. 4FMFDU 1SF"NQ.PE'Y     1XS"NQ3FWFSC 4X NOTE You can also select a block directly from within its parameter setting screen. To do so, press and hold the [STORE/ASSIGN] button (for at least one second) and continue from Step 5 below. 3 Press the [PRE-AMP], [MOD-FX], [PWR-AMP] (CP5 only), or [REVERB] button. With a block selected, you will now be asked to indicate which of its parameters is to be assigned. 4FMFDU QBSBNFUFS     #BTT5SFCMF  4QFFE NOTE If the currently selected part is not a left or right part, pressing of only the [REVERB] button will be accepted at this time. NOTE If a left or right part having a non-piano voice is currently selected, pressing of the [PRE-AMP] button will not be accepted at this time. 4 To select a parameter, press the corresponding knob. You will now be asked to indicate the knob to which the selected parameter is to be assigned. 4FMFDU BTTJHOBCMFLOPC -3FM -%NQ35JNF 5 Press the knob to be used to control the selected parameter. The display will return to the Performance screen, where you can confirm that the selected parameter is now assigned to the selected knob. HINT Removing Parameter Assignments To remove a knob's parameter assignment, navigate to Page 1 of the Performance screen, press and hold the [EXIT] button, and then press the knob in question. The parameter assignment will be canceled, and turning the knob will now have no effect on the sound of the Performance. NOTE Whenever a new voice, pre-amplifier, modulation effect, power-amplifier / compressor (CP5 only), or reverb type is selected within the current Performance (page 35), the parameters assigned to Knobs 1 to 3 may change automatically and knobs may be labeled as *** on the Performance screen to indicate that nothing is assigned. In such a case, parameters should be reassigned to Knobs 1 to 3 as required. Quick Start Guide 28 CP5/CP50 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Using Performances
28
CP5/CP50 Owner’s Manual
Quick Start Guide
2
Press and hold the [STORE/ASSIGN] button (for at least one second). You will be asked to select a block, and the
lamps to the top-left of the [PRE-AMP], [MOD-FX], [PWR-AMP] (CP5 only), and [REVERB] buttons will start to flash.
NOTE
You can also select a block directly from within its parameter setting screen. To do so, press and hold the [STORE/ASSIGN] button (for at
least one second) and continue from Step 5 below.
3
Press the [PRE-AMP], [MOD-FX], [PWR-AMP] (CP5 only), or [REVERB] button. With a block selected, you will now be
asked to indicate which of its parameters is to be assigned.
NOTE
If the currently selected part is not a left or right part, pressing of only the [REVERB] button will be accepted at this time.
NOTE
If a left or right part having a non-piano voice is currently selected, pressing of the [PRE-AMP] button will not be accepted at this time.
4
To select a parameter, press the corresponding knob. You will now be asked to indicate the knob to which the
selected parameter is to be assigned.
5
Press the knob to be used to control the selected parameter. The display will return to the Performance screen,
where you can confirm that the selected parameter is now assigned to the selected knob.
NOTE
Whenever a new voice, pre-amplifier, modulation effect, power-amplifier / compressor (CP5 only), or reverb type is selected within the current
Performance (page 35), the parameters assigned to Knobs 1 to 3 may change automatically and knobs may be labeled as *** on the Performance
screen to indicate that nothing is assigned. In such a case, parameters should be reassigned to Knobs 1 to 3 as required.
HINT
Removing Parameter Assignments
To remove a knob’s parameter assignment, navigate to Page 1 of the Performance screen, press and hold the [EXIT] button, and
then press the knob in question. The parameter assignment will be canceled, and turning the knob will now have no effect on the
sound of the Performance.
Select PreAmp
/
ModFx
/
PwrAmp
/
Reverb Sw.
Select parame
t
er.
Bass
Tre
b
le
Speed
Select assign
a
ble k
n
ob.
L1-Rel
L1-Dm
p
R Time