Yamaha CS1x Owner's Manual - Page 28

# LCD 0 off 1 PerfLevel (Performance Level) (page 23) 2 ArpgTempo (Arpeggiator Tempo) (page 23) 3 ArpgType (Arpeggiator Type) (page 23) 4 ArpgSubdiv (Arpeggiator Subdivide) (page 23) 5 MWCutoff (MW Cutoff) (page 25) 6 MWPModDpth (MW Pitch Modulation Depth) (page 25) 7 MWFModDpth (MW Filter Modulation Depth) (page 25) 8 PBRange (Pitch Bend Range) (page 25) 9 FCCutoff (FC Cutoff) (page 26) 10 FCFModDpth (FC Filter Modulation Depth) (page 26) 11 FCVariDpth (FC Variation Depth) (page 26) 12 PortaTime (Portamento Time) (page 26) 13 *FEGDcyTime (FEG Decay Time) (page 32) 14 *AEGDcyTime (AEG Decay Time) (page 30) 15 *ChoToRev (Chorus Send To Reverb) 16 *VariCntrl (Variation Control) 17 *RevChoSend (Reverb And Chorus Send) 18 *ChorusSend (Chorus Send) (page 38) 19 *ReverbSend (Reverb Send) (page 38) 20 *Pan (page 38) 21 *LFOSpeed (LFO Speed) (page 31) 22 *LFOPMod (Vibrato Depth) (page 30) 23 *VibDelay (Vibrato Delay) 24 *LFOAMod (LFO Amplitude Modulation Depth) (page 30) 25 *LFOFMod (LFO Filter Modulation Depth) (page 31) 26 *FEGAtkTime (FEG Attack Time) (page 32) 27 *FEGSusLvl (FEG Sustain Level) (page 32) 28 *FEGVelSens (FEG Level Velocity Sensitivity) 29 *Pitch (Oscillator Pitch) Parameters with an asterisk affect entire Layers in a Performance. You cannot directly edit them from the LCD, but you can assign them to the ASSIGN 1 knob. You can also select each parameter by inputting the corresponding number using the numeric keypad. Layer Edit 1 (independently applied to each Layer) The functions in this row provide various parameters mainly related to the keyboard such as Tune, Note Limit and Velocity. The parameters can be set for each Layer in a Performance. DEMO PERFORMANCE MULTI STORE UTILITY TUNE NOTE NOTE DETUNE LIMIT LIMIT SFT LOW HIGH AEG ATK DCY DCY REL TIME TIME LEVEL TIME FEG ATK DCY DCY REL TIME TIME LEVEL TIME BANK PROGRAM VOLUME PAN LIMIT LOW AMOD INIT LEVEL REV SEND VEL ASSIGN2 LIMIT OFFSET DEPTH PARAM DATA HIGH LFO PMOD FMOD WAVE SPEED PHASE INIT PEG ATK ATK DCY REL REL TIME LEVEL TIME TIME LEVEL EFFECT FILTER POLY/ CHO VARI CUTOFF REZ MONO SEND SEND LAYER s TUNE This sets the tuning of a Layer. There are two parameters, NOTE SFT (Note Shift) and DETUNE. Note Shift Detune NOTE SFT (Note Shift): Raises or lowers the pitch of the voice in semitones. Settings: -24 ~ +24 (semitones) DETUNE: Raises or lowers the pitch of the voice in fine increments or decrements (0.1 Hz each). Settings: -12.8 Hz ~ +12.7 Hz s NOTE This sets the range of notes that each Layer will play. There are two parameters, LIMIT LOW and LIMIT HIGH. Limit Low Limit High LIMIT LOW: Determines the low note limit, or the lowest note that will be played by the voice. LIMIT HIGH: Determines the high note limit, or the highest note that will be played by the voice. C-2 C1 C2 C3 C4 C5 C6 G8 0 36 Note Name 48 60 72 84 96 127 Note Number LIMIT LOW is set to C2 and LIMIT HIGH is set to C4. Range of notes that can be played. CS1x Keyboard Settings: LIMIT LOW: C-2 ~ G8 LIMIT HIGH: C-2 ~ G8 NOTE It is not possible to set the LIMIT LOW note above the LIMIT HIGH note, or the LIMIT HIGH note below the LIMIT LOW note. 27