Yamaha QL5 Ql Editor Owner's Manual - Page 72

Meter window, INPUT METER

Get Yamaha QL5 PDF manuals and user guides View all Yamaha QL5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Meter window This window shows the signal levels of each section in the QL, letting you check for the presence of signals and whether an overload is occurring. This window is divided into INPUT METER and OUTPUT METER; to switch pages, click the tabs located at the top of the window. NOTE In order to view the QL's signal levels in the Meter window, make sure that QL Editor and the QL itself are synchronized. Also, please make sure that the Level Meter is enabled in the System Setup dialog box ( ➥ p.2.) INPUT METER page 12 3 1 METERING POINT Select one of the following as the point where metering will occur. PRE G.C, PRE D.GAIN, POST D.GAIN, PRE FADER, POST ON 2 PEAK HOLD Switches peak hold on/off. 3 Meters These peak level meters show the input level of each channel. The current fader value is shown in the box below. If clipping occurs at any one of the detection points in the channel, the  segment will light. 72 QL Editor Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
QL Editor Owner’s Manual
72
This window shows the signal levels of each section in the QL, letting you check for the presence of signals and whether an
overload is occurring.
This window is divided into INPUT METER and OUTPUT METER; to switch pages, click the tabs located at the top of the
window.
In order to view the QL’s signal levels in the Meter window, make sure that QL Editor and the QL itself are
synchronized. Also, please make sure that the Level Meter is enabled in the System Setup dialog box
(
➥
p.2.)
INPUT METER page
1
METERING POINT
Select one of the following as the point where metering will occur.
PRE G.C, PRE D.GAIN, POST D.GAIN, PRE FADER, POST ON
2
PEAK HOLD
Switches peak hold on/off.
3
Meters
These peak level meters show the input level of each channel. The current fader value is shown in the box below.
If clipping occurs at any one of the detection points in the channel, the
segment will light.
Meter window
NOTE
1
2
3