Yamaha UW500 UW500 Owners Manual - Page 34

Hard Disk Recording, n Recording guitar sounds digitally

Get Yamaha UW500 PDF manuals and user guides View all Yamaha UW500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Hard Disk Recording You can record to hard disk using the UW500, the included sequence software (XGworks), and SoftSynthesizer (S-YXG50). The following section explains basic connections and procedures for recording guitar digitally to XGworks, then mastering it to a digital recorder (such as an MD recorder). NOTE For more information on using XGworks, refer to the included PDF manual. s Recording guitar sounds digitally computer XGworks Soft Synthesizer Set the INPUT SELECT to "MONO." UW500 headphones USB terminal INPUT 1/2 jack PHONES jack Set the INPUT 1 and 2 gain switches to "GUITAR." guitar effect unit guitar 1. Connect the guitar or guitar effect unit to the INPUT 1 or 2 jack using a shielded guitar cable (with standard plugs). Connect the headphones to the PHONES jack (page 12), or the powered speakers to the OUTPUT jacks (page 14). If you are using an external MIDI tone generator, connect it to the UW500's MIDI OUT terminal or the TO TG terminal (page 21). Connect the UW500's AUX IN jacks to the OUTPUT jacks of the tone generator. Before connecting, be sure to turn off the power to the UW500. NOTE If you wish to record your vocal and guitar accompaniment to separate files, connect the guitar and microphone to the INPUT 1 and 2 jacks and record them in stereo. Later, you can separate these into monaural Wave files using TWE. 2. Turn on the power to the UW500 by rotating the OUTPUT knob to the "ON" position. Lower the OUTPUT knob setting to minimum (just above the "ON" position). 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
34
Hard Disk Recording
You can record to hard disk using the UW500, the included sequence software
(XGworks), and SoftSynthesizer (S-YXG50). The following section explains basic
connections and procedures for recording guitar digitally to XGworks, then mastering
it to a digital recorder (such as an MD recorder).
For more information on using XGworks, refer to the included PDF manual.
■
Recording guitar sounds digitally
1.
Connect the guitar or guitar effect unit to the INPUT 1 or 2 jack using a
shielded guitar cable (with standard plugs).
Connect the headphones to the PHONES jack (page 12), or the powered
speakers to the OUTPUT jacks (page 14).
If you are using an external MIDI tone generator, connect it to the
UW500’s MIDI OUT terminal or the TO TG terminal (page 21). Connect
the UW500’s AUX IN jacks to the OUTPUT jacks of the tone generator.
Before connecting, be sure to turn off the power to the UW500.
If you wish to record your vocal and guitar accompaniment to separate
files, connect the guitar and microphone to the INPUT 1 and 2 jacks and
record them in stereo. Later, you can separate these into monaural Wave
files using TWE.
2.
Turn on the power to the UW500 by rotating the OUTPUT knob to the
“ON” position.
Lower the OUTPUT knob setting to minimum (just above the “ON” posi-
tion).
NOTE
computer
guitar
headphones
UW500
USB
terminal
guitar effect unit
INPUT 1/2 jack
PHONES
jack
Set the INPUT SELECT
to “MONO.”
Set the INPUT 1 and 2
gain switches to “GUITAR.”
XGworks
Soft
Synthesizer
NOTE