Home » ZyXEL Manuals » Wireless » ZyXEL VMG3925-B10B » Manual Viewer

ZyXEL VMG3925-B10B User Guide - Page 161

The DMZ Screen, The ALG Screen

Add to My Manuals
Save this manual to your list of manuals

Page 161 highlights

Chapter 11 Network Address Translation (NAT) Table 60 Port Triggering: Configuration Add/Edit (continued) LABEL Open Start Port DESCRIPTION The open port is a port (or a range of ports) that a server on the WAN uses when it sends out a particular service. The VMG forwards the traffic with this port (or range of ports) to the client computer on the LAN that requested the service. Open End Port Open Protocol OK Cancel Type a port number or the starting port number in a range of port numbers. Type a port number or the ending port number in a range of port numbers. Select the transport layer protocol from TCP, UDP, or TCP/UDP. Click OK to save your changes. Click Cancel to exit this screen without saving. 11.5 The DMZ Screen In addition to the servers for specified services, NAT supports a default server IP address. A default server receives packets from ports that are not specified in the NAT Port Forwarding Setup screen. Figure 83 Network Setting > NAT > DMZ The following table describes the fields in this screen. Table 61 Network Setting > NAT > DMZ LABEL DESCRIPTION Default Server Enter the IP address of the default server which receives packets from ports that are not Address specified in the NAT Port Forwarding screen. Apply Cancel Note: If you do not assign a Default Server Address, the VMG discards all packets received for ports that are not specified in the NAT Port Forwarding screen. Click Apply to save your changes. Click Cancel to restore your previously saved settings. 11.6 The ALG Screen Some NAT routers may include a SIP Application Layer Gateway (ALG). A SIP ALG allows SIP calls to pass through NAT by examining and translating IP addresses embedded in the data stream. When the VMG registers with the SIP register server, the SIP ALG translates the VMG's private IP address inside the SIP data stream to a public IP address. You do not need to use STUN or an outbound proxy if your VMG is behind a SIP ALG. Use this screen to enable and disable the NAT and SIP (VoIP) ALG in the VMG. To access this screen, click Network Setting > NAT > ALG. VMG3925-B10B User's Guide 161

Section	Page
VMG3925-B10B	1
Contents Overview	3
Table of Contents	5
User’s Guide	14
Introducing the VMG	15
1.1 Overview	15
1.2 Ways to Manage the VMG	15
1.3 Good Habits for Managing the VMG	15
1.4 Applications for the VMG	16
1.4.1 Internet Access	16
1.4.2 VMG’s USB Support	16
1.5 LEDs (Lights)	17
1.6 The RESET Button	19
1.7 Wireless Access	19
1.7.1 Using the Wi-Fi and WPS Buttons	19
The Web Configurator	21
2.1 Overview	21
2.1.1 Accessing the Web Configurator	21
2.2 Web Configurator Layout	23
2.2.1 Title Bar	23
2.2.2 Navigation Panel	24
Quick Start	28
3.1 Overview	28
3.2 Quick Start Setup	28
Tutorials	30
4.1 Overview	30
4.2 Setting Up an ADSL PPPoE Connection	30
4.3 Setting Up a Secure Wireless Network	33
4.3.1 Configuring the Wireless Network Settings	33
4.3.2 Using WPS	34
4.3.3 Without WPS	38
4.4 Setting Up Multiple Wireless Groups	39
4.5 Configuring Static Route for Routing to Another Network	42
4.6 Configuring QoS Queue and Class Setup	44
4.7 Access the VMG Using DDNS	48
4.7.1 Registering a DDNS Account on www.dyndns.org	48
4.7.2 Configuring DDNS on Your VMG	49
4.7.3 Testing the DDNS Setting	49
4.8 Configuring the MAC Address Filter	49
4.9 Access Your Shared Files From a Computer	50
Technical Reference	52
Network Map and Status Screens	53
5.1 Overview	53
5.2 The Network Map Screen	53
5.3 The Status Screen	54
Broadband	57
6.1 Overview	57
6.1.1 What You Can Do in this Chapter	57
6.1.2 What You Need to Know	58
6.1.3 Before You Begin	60
6.2 The Broadband Screen	61
6.2.1 Add/Edit Internet Connection	62
6.3 The 3G Backup Screen	70
6.4 The Advanced Screen	74
6.5 The 802.1x Screen	76
6.5.1 Modify 802.1X Settings	77
6.6 Technical Reference	78
Wireless	84
7.1 Overview	84
7.1.1 What You Can Do in this Chapter	84
7.1.2 What You Need to Know	84
7.2 The General Screen	85
7.2.1 No Security	87
7.2.2 Basic (WEP Encryption)	87
7.2.3 More Secure (WPA(2)-PSK)	88
7.3 The Guest / More AP Screen	89
7.3.1 Edit Guest / More AP	90
7.4 The WPS Screen	92
7.5 The WMM Screen	94
7.6 The WDS Screen	95
7.6.1 WDS Scan	96
7.7 The Others Screen	97
7.8 The Channel Status Screen	98
7.9 Technical Reference	99
7.9.1 Wireless Network Overview	99
7.9.2 Additional Wireless Terms	101
7.9.3 Wireless Security Overview	101
7.9.4 Signal Problems	103
7.9.5 BSS	104
7.9.6 MBSSID	104
7.9.7 Preamble Type	105
7.9.8 Wireless Distribution System (WDS)	105
7.9.9 WiFi Protected Setup (WPS)	105
Home Networking	113
8.1 Overview	113
8.1.1 What You Can Do in this Chapter	113
8.1.2 What You Need To Know	114
8.1.3 Before You Begin	115
8.2 The LAN Setup Screen	115
8.3 The Static DHCP Screen	119
8.4 The UPnP Screen	120
8.4.1 Turning On UPnP in Windows 7 Example	121
8.5 The Additional Subnet Screen	122
8.6 The STB Vendor ID Screen	124
8.7 The Wake on LAN Screen	124
8.8 The TFTP Server Name Screen	125
8.9 Technical Reference	125
8.9.1 LANs, WANs and the VMG	125
8.9.2 DHCP Setup	126
8.9.3 DNS Server Addresses	126
8.9.4 LAN TCP/IP	127
Routing	129
9.1 Overview	129
9.2 The Routing Screen	129
9.2.1 Add/Edit Static Route	130
9.3 The DNS Route Screen	131
9.3.1 The DNS Route Add Screen	131
9.4 The Policy Route Screen	132
9.4.1 Add/Edit Policy Route	133
9.5 RIP	134
9.5.1 The RIP Screen	134
Quality of Service (QoS)	135
10.1 Overview	135
10.1.1 What You Can Do in this Chapter	135
10.2 What You Need to Know	136
10.3 The Quality of Service General Screen	137
10.4 The Queue Setup Screen	138
10.4.1 Adding a QoS Queue	139
10.5 The Classification Setup Screen	140
10.5.1 Add/Edit QoS Class	141
10.6 The QoS Shaper Setup Screen	145
10.6.1 Add/Edit a QoS Shaper	146
10.7 The QoS Policer Setup Screen	146
10.7.1 Add/Edit a QoS Policer	147
10.8 Technical Reference	148
Network Address Translation (NAT)	153
11.1 Overview	153
11.1.1 What You Can Do in this Chapter	153
11.1.2 What You Need To Know	153
11.2 The Port Forwarding Screen	154
11.2.1 Add/Edit Port Forwarding	156
11.3 The Applications Screen	157
11.3.1 Add New Application	157
11.4 The Port Triggering Screen	158
11.4.1 Add/Edit Port Triggering Rule	160
11.5 The DMZ Screen	161
11.6 The ALG Screen	161
11.7 The Address Mapping Screen	162
11.7.1 Add/Edit Address Mapping Rule	163
11.8 The Sessions Screen	164
11.9 Technical Reference	164
11.9.1 NAT Definitions	165
11.9.2 What NAT Does	165
11.9.3 How NAT Works	166
11.9.4 NAT Application	166
Dynamic DNS Setup	169
12.1 Overview	169
12.1.1 What You Can Do in this Chapter	169
12.1.2 What You Need To Know	169
12.2 The DNS Entry Screen	170
12.2.1 Add/Edit DNS Entry	170
12.3 The Dynamic DNS Screen	171
Vlan Group	172
13.1 Overview	172
13.1.1 What You Can Do in this Chapter	172
13.2 The Vlan Group Screen	172
13.2.1 Add/Edit a VLAN Group	173
Interface Group	174
14.1 Overview	174
14.1.1 What You Can Do in this Chapter	174
14.2 The Interface Group Screen	174
14.2.1 Interface Group Configuration	175
14.2.2 Interface Grouping Criteria	177
USB Service	179
15.1 Overview	179
15.1.1 What You Can Do in this Chapter	179
15.1.2 ().What You Need To Know	179
15.1.3 Before You Begin	180
15.2 The File Sharing Screen	180
15.2.1 The Add New User Screen	181
15.3 The Media Server Screen	182
Firewall	184
16.1 Overview	184
16.1.1 What You Can Do in this Chapter	184
16.1.2 What You Need to Know	185
16.2 The Firewall Screen	185
16.3 The Protocol Screen	186
16.3.1 Add/Edit a Service	187
16.4 The Access Control Screen	188
16.4.1 Add/Edit an ACL Rule	189
16.5 The DoS Screen	190
MAC Filter	192
17.1 Overview	192
17.2 The MAC Filter Screen	192
Parental Control	194
18.1 Overview	194
18.2 The Parental Control Screen	194
18.2.1 Add/Edit a Parental Control Profile	195
Scheduler Rule	198
19.1 Overview	198
19.2 The Scheduler Rule Screen	198
19.2.1 Add/Edit a Schedule	198
Certificates	200
20.1 Overview	200
20.1.1 What You Can Do in this Chapter	200
20.2 What You Need to Know	200
20.3 The Local Certificates Screen	200
20.3.1 Create Certificate Request	201
20.3.2 Load Signed Certificate	203
20.4 The Trusted CA Screen	204
20.4.1 View Trusted CA Certificate	204
20.4.2 Import Trusted CA Certificate	205
Log	207
21.1 Overview	207
21.1.1 What You Can Do in this Chapter	207
21.1.2 What You Need To Know	207
21.2 The System Log Screen	208
21.3 The Security Log Screen	208
Traffic Status	210
22.1 Overview	210
22.1.1 What You Can Do in this Chapter	210
22.2 The WAN Status Screen	210
22.3 The LAN Status Screen	211
22.4 The NAT Status Screen	212
ARP Table	213
23.1 Overview	213
23.1.1 How ARP Works	213
23.2 ARP Table Screen	213
Routing Table	215
24.1 Overview	215
24.2 The Routing Table Screen	215
Multicast Status	217
25.1 Overview	217
25.2 The IGMP Status Screen	217
25.3 The MLD Status Screen	217
xDSL Statistics	219
26.1 The xDSL Statistics Screen	219
3G Statistics	222
27.1 Overview	222
27.2 The 3G Statistics Screen	222
System	224
28.1 Overview	224
28.2 The System Screen	224
User Account	225
29.1 Overview	225
29.2 The User Account Screen	225
29.2.1 The User Account Add/Edit Screen	225
Remote Management	227
30.1 Overview	227
30.2 The Remote MGMT Screen	227
30.3 The Trust Domain Screen	228
30.4 The Add Trust Domain Screen	228
TR-064	230
31.1 Overview	230
31.2 The TR-064 Screen	230
TR-069 Client	231
32.1 Overview	231
32.2 The TR-069 Client Screen	231
SNMP	233
33.1 Overview	233
33.2 The SNMP Screen	233
Time Settings	235
34.1 Overview	235
34.2 The Time Screen	235
E-mail Notification	237
35.1 Overview	237
35.2 The Email Notification Screen	237
35.2.1 Email Notification Edit	237
Log Setting	239
36.1 Overview	239
36.2 The Log Settings Screen	239
36.2.1 Example E-mail Log	240
Firmware Upgrade	242
37.1 Overview	242
37.2 The Firmware Screen	242
Backup Restore	245
38.1 Overview	245
38.2 The Backup Restore Screen	245
38.3 The ROM-D Screen	247
38.4 The Reboot Screen	247
Diagnostic	248
39.1 Overview	248
39.1.1 What You Can Do in this Chapter	248
39.2 What You Need to Know	248
39.3 Ping & TraceRoute & NsLookup	249
39.4 802.1ag	249
39.5 OAM Ping	250
Troubleshooting	253
40.1 Power, Hardware Connections, and LEDs	253
40.2 VMG Access and Login	254
40.3 Internet Access	256
40.4 Wireless Internet Access	257
40.5 USB Device Connection	258
40.6 UPnP	258
Appendices	260
Customer Support	261
Wireless LANs	267
IPv6	280
Services	288
Legal Information	292

Match case Limit results 1 per page

Chapter 11 Network Address Translation (NAT)

VMG3925-B10B User’s Guide

161

11.5

The DMZ Screen

In addition to the servers for specified services, NAT supports a default server IP address. A default

server receives packets from ports that are not specified in the

NAT Port Forwarding Setup

screen.

Figure 83

Network Setting > NAT > DMZ

The following table describes the fields in this screen.

11.6

The ALG Screen

Some NAT routers may include a SIP Application Layer Gateway (ALG). A SIP ALG allows SIP calls

to pass through NAT by examining and translating IP addresses embedded in the data stream.

When the VMG registers with the SIP register server, the SIP ALG translates the VMG’s private IP

address inside the SIP data stream to a public IP address. You do not need to use STUN or an

outbound proxy if your VMG is behind a SIP ALG.

Use this screen to enable and disable the NAT and SIP (VoIP) ALG in the VMG. To access this

screen, click

Network Setting > NAT > ALG

Open Start Port

The open port is a port (or a range of ports) that a server on the WAN uses when it sends

out a particular service. The VMG forwards the traffic with this port (or range of ports) to the

client computer on the LAN that requested the service.

Type a port number or the starting port number in a range of port numbers.

Open End Port

Type a port number or the ending port number in a range of port numbers.

Open Protocol

Select the transport layer protocol from

TCP

UDP

, or

TCP/UDP

Click

to save your changes.

Cancel

Click

Cancel

to exit this screen without saving.

Table 60

Port Triggering: Configuration Add/Edit (continued)

LABEL

DESCRIPTION

Table 61

Network Setting > NAT > DMZ

LABEL

DESCRIPTION

Default Server

Address

Enter the IP address of the default server which receives packets from ports that are not

specified in the

NAT Port Forwarding

screen.

Note: If you do not assign a

Default Server Address

, the VMG discards all packets received

for ports that are not specified in the

NAT Port Forwarding

screen.

Apply

Click

Apply

to save your changes.

Cancel

Click

Cancel

to restore your previously saved settings.