Adaptec 3405 User Guide - Page 115

Creating the Firmware Update Disks, Running the Menu-based AFU

Get Adaptec 3405 - RAID Controller PDF manuals and user guides
UPC - 760884155028
View all Adaptec 3405 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 115 highlights

Appendix E: Using the Adaptec Flash Utility ● 115 Creating the Firmware Update Disks To create the firmware update disks: 1 Copy these files to empty, formatted floppy disks, a USB flash drive, or a writable CD: ● AFU.exe ● Axxxx01.ufi where xxx is the model number of your controller. Note: Most controller model numbers have a suffix (for example Adaptec RAID 3405). Check that the .ufi file is the correct file for your controller before copying. 2 If using floppy disks, copy each additional Axxxx0x.ufi file to a separate floppy disk. (Some RAID controllers have two UFI files; some have four. Each goes onto its own floppy disk.) 3 To use a menu-based AFU, see the following section. To run the AFU from the command line, see page 116. Running the Menu-based AFU To run the menu-based AFU: 1 Shut down your operating system and reboot to DOS from a bootable MS-DOS floppy disk or from a DOS partition on a bootable drive. (You can use a disk drive connected to the controller you are updating.) If your computer isn't set up to boot from the bootable floppy disk, enter the system setup utility and change the setting. 2 Insert the firmware update disk (created using the steps above) containing AFU.exe 3 At the DOS command prompt, type AFU with no arguments. The AFU's main menu is displayed. 4 Select Select Controllers, then select the Adaptec RAID controller(s) to be flashed. To update multiple RAID controllers in the same system, update the boot controller's flash first, restart the computer, then update the flash for the remaining controllers. 5 Select Select an Operation. 6 Choose the operation you want, then follow the on-screen instructions to complete the task: ● Update flash image-Updates all the flash components on a RAID controller with the flash image data from the UFI file. ● Save flash image-Reads the contents of a RAID controller's flash components and saves the data to a UFI file, which you can use to restore a RAID controller's flash if required. ● Verify flash image-Reads the contents of a RAID controller's flash components and compares it to the contents of the specified UFI file. ● Display flash information-Displays version information about a RAID controller's flash components. ● List flash image-Lists all supported RAID controllers detected on your system.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Appendix E: Using the Adaptec Flash Utility
●
115
Creating the Firmware Update Disks
To create the firmware update disks:
1
Copy these files to empty, formatted floppy disks, a USB flash drive, or a writable CD:
●
AFU.exe
●
Ax
xxx
01.ufi
where
xxx
is the model number of your controller.
Note:
Most controller model numbers have a suffix (for example Adaptec RAID 3405).
Check that the .ufi file is the correct file for your controller before copying.
2
If using floppy disks, copy each additional Axxxx0x.ufi file to a separate floppy disk. (Some
RAID controllers have two UFI files; some have four. Each goes onto its own floppy disk.)
3
To use a menu-based AFU, see the following section.
To run the AFU from the command line, see
page 116
.
Running the Menu-based AFU
To run the menu-based AFU:
1
Shut down your operating system and reboot to DOS from a bootable MS-DOS floppy
disk or from a DOS partition on a bootable drive. (You can use a disk drive connected to
the controller you are updating.) If your computer isn’t set up to boot from the bootable
floppy disk, enter the system setup utility and change the setting.
2
Insert the firmware update disk (created using the steps above) containing AFU.exe
3
At the DOS command prompt, type
AFU
with no arguments.
The AFU’s main menu is displayed.
4
Select
Select Controllers
, then select the Adaptec RAID controller(s) to be flashed.
To update multiple RAID controllers in the same system, update the boot controller’s flash
first, restart the computer, then update the flash for the remaining controllers.
5
Select
Select an Operation
.
6
Choose the operation you want, then follow the on-screen instructions to complete the
task:
●
Update flash image
—Updates all the flash components on a RAID controller with the
flash image data from the UFI file.
●
Save flash image
—Reads the contents of a RAID controller’s flash components and
saves the data to a UFI file, which you can use to restore a RAID controller’s flash if
required.
●
Verify flash image
—Reads the contents of a RAID controller’s flash components and
compares it to the contents of the specified UFI file.
●
Display flash information
—Displays version information about a RAID controller’s
flash components.
●
List flash image
—Lists all supported RAID controllers detected on your system.