Airlink AML001 Manual - Page 37

progress messages are affected by this command., Displays result codes as digits. Numerical mode.

Get Airlink AML001 PDF manuals and user guides View all Airlink AML001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

PCI Modem Card User's Manual Q0 Enables result codes (default). Q1 Disables result codes. S=-S Register Control Use this command to view or change an S-register. S-registers contain parameters used by the modem. This command has two forms: one to show the contents of the register and one to change the contents of the register. Some registers are read only and are not affected by the S= command. Each register has a specific function. S? S= Displays register contents. Sets the contents of the register to if the register is not read only. T-Select Tone Dialing Use this command to configure the modem for DTMF tone dialing. All subsequent D commands use tone dialing until either the P command or a pulse dial modifier is received by the modem. Tone dialing is the default setting. Do not supply parameters with this command unless it is used as part of a dial modifier. V-DCE Response Format The result codes using one of two formats. Verbose mode generates result codes in a text format using words. Numerical mode generates result codes as a number. Each result code has a number assigned to it. Use this command to switch between numerical and verbose modes. Call progress and negotiation progress messages are affected by this command. V0 Displays result codes as digits. Numerical mode. V1 Displays result codes as text (default). Verbose mode. W-Result Code Option Use this command to select the modems CONNECT message options. W0 CONNECT result code reports DTE receive speed. Disables protocol result codes. W1 CONNECT result code reports DTE receive speed. Enables protocol result codes. W2 CONNECT result code reports DCE receive speed. Enables protocol result codes (default). X-Extended Result Codes Control Use this command to select which result codes are used by the modem. The 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
PCI Modem Card User’s Manual
36
Q0
Enables result codes (default).
Q1
Disables result codes.
S<register_number>=<value>±S Register Control
Use this command to view or change an S-register. S-registers contain
parameters used by the modem. This command has two forms: one to show
the contents of the register and one to change the contents of the register.
Some registers are read only and are not affected by the
S<register
number>=<value>
command. Each register has a specific function.
S<register_number>?
Displays register contents.
S<register_number>=<value>
Sets the contents of the register to
<value> if the register is not read only.
T±Select Tone Dialing
Use this command to configure the modem for DTMF tone dialing. All
subsequent
D<dial string>
commands use tone dialing until either the
P
command or a pulse dial modifier is received by the modem. Tone dialing is
the default setting. Do not supply parameters with this command unless it is
used as part of a dial modifier.
V<value>±DCE Response Format
The result codes using one of two formats. Verbose mode generates result
codes in a text format using words. Numerical mode generates result codes as
a number. Each result code has a number assigned to it. Use this command to
switch between numerical and verbose modes. Call progress and negotiation
progress messages are affected by this command.
V0
Displays result codes as digits. Numerical mode.
V1
Displays result codes as text (default). Verbose mode.
W<value>±Result Code Option
Use this command to select the modems CONNECT message options.
W0
CONNECT result code reports DTE receive speed. Disables
protocol result codes.
W1
CONNECT result code reports DTE receive speed. Enables
protocol result codes.
W2
CONNECT result code reports DCE receive speed. Enables
protocol result codes (default).
X<value>±Extended Result Codes Control
Use this command to select which result codes are used by the modem. The